Removal [10/2015 - 07/2021]: Procedure

Refer to REMOVAL [10/2015 - ]

Refer to PROCEDURE - Step 3 [10/2015 - 08/2016] , or refer to PROCEDURE - Step 3 [08/2016 - 08/2019] , or refer to PROCEDURE - Step 3 [08/2019 - ]

1. Remove the screw.
2. Disengage the clamp and remove the hood lock control cable cover.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the 2 clips.
2. Disengage the clamp to remove the hood lock release lever protector.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the connector.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Remove the 3 bolts.
3. Disconnect the hood lock control cable assembly to remove the hood lock assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Refer to PROCEDURE - Step 7 [10/2015 - 08/2016] , or refer to PROCEDURE - Step 7 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 7 , or refer to PROCEDURE - Step 7 [03/2018 - 08/2019] , or refer to PROCEDURE - Step 7 [08/2019 - ]

Refer to PROCEDURE - Step 8 [10/2015 - 08/2016] , or refer to PROCEDURE - Step 8 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 8 [12/2017 - 03/2018] , or refer to PROCEDURE - Step 8 [03/2018 - 08/2019] , or refer to PROCEDURE - Step 8 [08/2019 - ]

1. for Type A:
   1. Disconnect the hood lock control cable assembly to remove the hood lock control lever sub-assembly.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      When changing the hood lock control lever sub-assembly from type A to type B, the hood lock control cable assembly must also be changed to type B.

2. for Type B:
   1. Disconnect the hood lock control cable assembly to remove the hood lock control lever sub-assembly.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      When changing the hood lock control lever sub-assembly from type B to type A, the hood lock control cable assembly must also be changed to type A.

1. Using a screwdriver, disengage the clamp as shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Hood Lock Control Cable Assembly
   *a	Clamp

2. Tie a string to the hood lock control lever sub-assembly side end of the hood lock control cable assembly.

   HINT: 

   Use a length of string long enough to pass through the engine compartment.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

3. Pull the hood lock control cable assembly through the grommet.

   HINT: 

   Leave the string inside the grommet.

4. Disconnect the string from the hood lock control cable assembly.
5. Using a screwdriver, disengage the 3 clamps as shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Hood Lock Control Cable Assembly	-	-
   *a	Clamp	-	-

   HINT: 

   Tape the screwdriver tip before use.

6. Pull the hood lock control cable assembly from the engine compartment to remove it.

   HINT: 

   • When changing the hood lock control cable assembly from type A to type B, the hood lock control lever sub-assembly must also be changed to type B.
   • When changing the hood lock control cable assembly from type B to type A, the hood lock control lever sub-assembly must also be changed to type A.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *A	Type A
   *B	Type B