LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2022 >> RX 350L FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 3 (Automatic Transmission [U881F] - Service Information (1 Of 2)) >> Valve Body Assembly >> Inspection [09/2015 - ] >> Procedure

Inspection [09/2015 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSPECT SHIFT SOLENOID VALVE S1 
    1. Measure the resistance according to the value(s) in the table below.
      GTY663166Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Shift Solenoid Valve S1)

      Standard Resistance

      Tester Connection Condition Specified Condition
      Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body 20°C (68°F) 11 to 15 Ω

      If the result is not as specified, replace the shift solenoid valve S1.

    2. Connect a positive (+) lead from the battery to the terminal of the shift solenoid valve S1 connector and a negative (-) lead to the shift solenoid valve S1 body, and check that the shift solenoid valve S1 moves and makes an operating sound.
      NOTE:

      When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

      OK

      The shift solenoid valve S1 moves and makes an operating sound.

      If the result is not as specified, replace the shift solenoid valve S1.

  2. INSPECT SHIFT SOLENOID VALVE S2 

    HINT: 

    Refer to Inspect Shift Solenoid Valve S1.

  3. INSPECT SHIFT SOLENOID VALVE SLU 
    1. Measure the resistance according to the value(s) in the table below.
      GTY634337Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Shift Solenoid Valve SLU)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω

      If the result is not as specified, replace the shift solenoid valve SLU.

    2. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the shift solenoid valve SLU connector, and check that the shift solenoid valve SLU moves and makes an operating sound.
      NOTE:

      When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

      OK

      The shift solenoid valve SLU moves and makes an operating sound.

      If the result is not as specified, replace the shift solenoid valve SLU.

  4. INSPECT SHIFT SOLENOID VALVE SL1 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLU.

  5. INSPECT SHIFT SOLENOID VALVE SL2 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLU.

  6. INSPECT SHIFT SOLENOID VALVE SL3 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLU.

  7. INSPECT SHIFT SOLENOID VALVE SL4 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLU.

  8. INSPECT SHIFT SOLENOID VALVE SL5 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLU.

  9. INSPECT SHIFT SOLENOID VALVE SLT 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLU.

scientia non olet · About LEMON Manuals