Caution / Notice / Hint
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear shock absorber assembly removal/installation are shown below.
NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED (FOR HEV MODEL)
| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| Rear wheel alignment adjustment | Perform "Calibration" |
|
Refer to RESET MEMORY / CALIBRATION [11/2021 - ] |
| Tires |
|
Tire Pressure Warning System | Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) Refer to WORK PROCEDURE [03/2024 - ] |
| Rear television camera assembly optical axis (Back camera position setting)*3 | Parking Assist Monitor System | Refer to CALIBRATION [11/2021 - ] | |
| Parking assist ECU initialization*3 | Panoramic View Monitor System | Refer to CALIBRATION [03/2024 - ] | |
| Advanced Park | Refer to CALIBRATION [03/2024 - ] | ||
| Suspension parts | Rear television camera assembly optical axis (Back camera position setting) | Parking Assist Monitor System | Refer to CALIBRATION [11/2021 - ] |
| Parking assist ECU initialization | Panoramic View Monitor System | Refer to CALIBRATION [03/2024 - ] | |
| Advanced Park | Refer to CALIBRATION [03/2024 - ] | ||
| Perform headlight ECU sub-assembly LH initialization | Lighting System (w/ Automatic Headlight Beam Level Control System) | Refer to INITIALIZATION [03/2022 - ] | |
| Rear height control sensor sub-assembly LH | Perform headlight ECU sub-assembly LH initialization | Lighting System (w/ Automatic Headlight Beam Level Control System) | Refer to INITIALIZATION [03/2022 - ] |
*1: Also necessary after performing a tire rotation.
*2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.
*3: The vehicle height changes because of tire replacement.
NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED (FOR GASOLINE MODEL)
| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| Rear wheel alignment adjustment |
|
|
Refer to RESET MEMORY / CALIBRATION [11/2021 - ] |
| Tires |
|
Tire Pressure Warning System | Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) Refer to WORK PROCEDURE [03/2024 - ] |
| Rear television camera assembly optical axis (Back camera position setting)*3 | Parking Assist Monitor System | Refer to CALIBRATION [11/2021 - ] | |
| Parking assist ECU initialization*3 | Panoramic View Monitor System | Refer to CALIBRATION [03/2024 - ] | |
| Advanced Park | Refer to CALIBRATION [03/2024 - ] | ||
| ECU Data Initialization (When performing tire replacement after RoB code X2104 is output) | Dynamic Torque Control AWD System | Refer to CALIBRATION [03/2023 - ] | |
| Suspension parts | Rear television camera assembly optical axis (Back camera position setting) | Parking Assist Monitor System | Refer to CALIBRATION [11/2021 - ] |
| Parking assist ECU initialization | Panoramic View Monitor System | Refer to CALIBRATION [03/2024 - ] | |
| Advanced Park | Refer to CALIBRATION [03/2024 - ] | ||
| Perform headlight ECU sub-assembly LH initialization | Lighting System (w/ Automatic Headlight Beam Level Control System) | Refer to INITIALIZATION [03/2022 - ] | |
| Rear height control sensor sub-assembly LH | Perform headlight ECU sub-assembly LH initialization | Lighting System (w/ Automatic Headlight Beam Level Control System) | Refer to INITIALIZATION [03/2022 - ] |
*1: Also necessary after performing a tire rotation.
*2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.
*3: The vehicle height changes because of tire replacement.
HINT:
- Use the same procedure for the RH and LH sides.
- The following procedure is for the LH side.
COMPONENTS (REMOVAL)
| Callout - Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 1 | REAR WHEEL | - | - | - | - |
| 2 | NO. 1 LOWER CONTROL ARM COVER | 48738B | - | - | - |
| 3 | REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (for LH Side with Height Control Sensor) | 89408C | - | - | - |
| 4 | LOOSEN REAR SHOCK ABSORBER ASSEMBLY | 48540 | See step 4 | - | - |
| 5 | NO. 2 PARKING BRAKE WIRE ASSEMBLY (w/ AVS) | 890C0A | - | - | - |
| 6 | SEPARATE REAR SHOCK ABSORBER ASSEMBLY | 48540 | See step 6 | - | - |
| 7 | REAR UPPER CONTROL ARM ASSEMBLY | 48790 | See step 7 | - | - |
| 8 | REMOVE REAR SHOCK ABSORBER ASSEMBLY | 48540 | See step 8 | - | - |
| *A | w/ AVS | *B | w/o AVS |
| *C | for LH Side with Height Control Sensor | - | - |
| *1 | PLATE WASHER | - | - |
| Callout - Procedure | Part Name Code | ||||
|---|---|---|---|---|---|
| 9 | REAR SHOCK ABSORBER CAP | 48554A | See step 9 | - | - |
| 10 | REAR SUSPENSION SUPPORT ASSEMBLY | 48760B | See step 10 | - | - |
| *1 | REAR SHOCK ABSORBER ASSEMBLY | - | - |
| • | Non-reusable part | * | Precoated part |