LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2022 >> LS 500 Base, RWD >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Restraint System - Service Information (4 Of 4) >> SIDE AIRBAG SENSOR (for Front Door) >> Removal [10/2020 - 10/2022] >> Procedure

Removal [10/2020 - 10/2022]: Procedure

  1. PRECAUTION 
    WARNING:

    Be sure to read precaution thoroughly before servicing.

    Refer to PRECAUTION [10/2020 - 11/2021] , or refer to PRECAUTION [11/2021 - 10/2023]

    GTY824211Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    NOTE:

    After the engine switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

    Refer to PRECAUTION [10/2020 - 10/2023]

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 25

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 

    Refer to PROCEDURE - Step 4

    WARNING:
    • Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
    • If the airbag deploys for any reason, it may cause a serious accident.
    GTY581108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE FRONT DOOR UPPER TRIM COVER LH 

    Refer to PROCEDURE - Step 4

  5. REMOVE FRONT DOOR ARMREST COVER LH 

    Refer to PROCEDURE - Step 5

  6. REMOVE FRONT DOOR NO. 2 ARMREST COVER LH 

    Refer to PROCEDURE - Step 6

  7. REMOVE COURTESY LIGHT ASSEMBLY 

    Refer to REMOVAL [12/2017 - ]

  8. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 7

  9. REMOVE FRONT DOOR SERVICE HOLE COVER LH 

    Refer to PROCEDURE - Step 23

  10. REMOVE DOOR SIDE AIRBAG SENSOR LH 
    1. Check that the engine switch is off.
    2. Check that the cable is disconnected from the negative (-) battery terminal.
      WARNING:
      • Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
        GTY581108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • If this procedure is performed without disconnecting the negative (-) battery terminal, the airbag may deploy even if an impact is applied only to the door side airbag sensor LH. Therefore, make sure that the negative (-) battery terminal is disconnected before performing this procedure.
        GTY796829Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the nut.
      GTY799021Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Pull Out
      NOTE:

      Do not reuse the nut.

    4. Detach the claw and pull out the door side airbag sensor LH.
      NOTE:

      If the door side airbag sensor LH has been dropped, replace it with a new one.

    5. Disconnect the airbag connector.
      NOTE:

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

      1. Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)
        GTY817693Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Housing Lock *b CPA
        *c CPA Upper Part *d Connector Lock is Released
      2. Push the housing lock again and disconnect the connector.
        NOTE:

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the airbag connector.

      3. After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.
        GTY824218Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a CPA *b Housing
        *c Correct *d Incorrect
scientia non olet · About LEMON Manuals