LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2022 >> LS 500 Base, RWD >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Monitor System - Service Information (1 Of 2) >> ULTRASONIC SENSOR (for Front) >> Removal [10/2023 - ] >> Procedure

Removal [10/2023 - ]: Procedure

  1. REMOVE FRONT BUMPER ASSEMBLY 
    1. for Sport Package:

      Refer to REMOVAL [10/2023 - ]

    2. except Sport Package:

      Refer to REMOVAL [10/2023 - ]

  2. REMOVE NO. 4 ENGINE ROOM WIRE 
    1. for Sport Package:

      Refer to PROCEDURE - Step 10

    2. except Sport Package:

      Refer to PROCEDURE - Step 10

  3. REMOVE FRONT SIDE ULTRASONIC SENSOR (w/ Advanced Park) 
    1. Detach the claw and remove the front side ultrasonic sensor.
      NOTE:

      Before removing the sensor, make sure to mark the sensor and front bumper cover so that each sensor can be returned to its original position.

      1. except Sport Package:
        GTY967587Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. for Sport Package:
        GTY1239404Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE FRONT SIDE ULTRASONIC SENSOR RETAINER (w/ Advanced Park) 

    HINT: 

    • Perform the following procedure only when replacement of a front side ultrasonic sensor retainer is necessary.
    • When removing the front side ultrasonic sensor retainer, if the double-sided tape is difficult to remove, heat the adhesive of the front side ultrasonic sensor retainer and front bumper assembly using a heat light.
    1. Heat the front bumper assembly and front side ultrasonic sensor retainer using a heat light.
      WARNING:
      GTY812853Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Heated Part
      *b Heat Light
      • Do not touch the heat light and heated parts.
      • Touching the heat light may result in burns.
      • Touching heated parts for a long time may result in burns.

      Standard

      Item Temperature
      Front Bumper Assembly 20 to 30°C (68 to 86°F)
      Front Side Ultrasonic Sensor Retainer
    2. Remove the front side ultrasonic sensor retainer.
      1. except Sport Package:
        GTY966367Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. for Sport Package:
        GTY1231966Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE NO. 2 ULTRASONIC SENSOR CLIP (w/ Advanced Park) 
    1. Detach the claw and remove the No. 2 ultrasonic sensor clip.
      1. except Sport Package:
        GTY966431Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. for Sport Package:
        GTY1239405Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE FRONT CORNER ULTRASONIC SENSOR 
    1. Detach the claw and remove the front corner ultrasonic sensor.
      NOTE:

      Before removing the sensor, make sure to mark the sensor and front bumper assembly so that each sensor can be returned to its original position.

      1. except Sport Package:
        GTY967584Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. for Sport Package:
        GTY967612Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER 

    HINT: 

    When removing the front corner ultrasonic sensor retainer, heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.

    1. Heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.
      WARNING:
      GTY812853Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Heated Part
      *b Heat Light
      • Do not touch the heat light and heated parts.
      • Touching the heat light may result in burns.
      • Touching heated parts for a long time may result in burns.

      Standard

      Item Temperature
      Front Bumper Assembly 20 to 30°C (68 to 86°F)
      Front Corner Ultrasonic Sensor Retainer
    2. Remove the front corner ultrasonic sensor retainer.
      1. except Sport Package:
        GTY966377Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. for Sport Package:
        GTY966378Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE FRONT CENTER ULTRASONIC SENSOR 
    1. Detach the claw and remove the front center ultrasonic sensor.
      NOTE:

      Before removing the sensor, make sure to mark the sensor and front bumper assembly so that each sensor can be returned to its original position.

      1. except Sport Package:
        GTY966429Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. for Sport Package:
        GTY967576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE FRONT ULTRASONIC SENSOR CLIP 

    HINT: 

    When removing the front ultrasonic sensor clip, heat the front bumper assembly and front ultrasonic sensor clip using a heat light.

    1. w/ Headlight Cleaner System:
      GTY966866Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Detach the washer hose clamp.

        HINT: 

        Use the same procedure for the other side.

    2. Heat the front bumper assembly and front ultrasonic sensor clip using a heat light.
      WARNING:
      • Do not touch the heat light and heated parts.
      • Touching the heat light may result in burns.
      • Touching heated parts for a long time may result in burns.
      GTY835518Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Heated Part
      *b Heat Light

      Standard

      Item Temperature
      Front Bumper Assembly 20 to 30°C (68 to 86°F)
      Front Ultrasonic Sensor Clip
    3. Remove the front ultrasonic sensor clip.
      1. except Sport Package:
        GTY966354Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. for Sport Package:
        GTY966355Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE FRONT NO. 2 ULTRASONIC SENSOR CLIP (w/ Advanced Park) 

    HINT: 

    • Perform the following procedure only when replacement of a front side ultrasonic sensor retainer is necessary.
    • When removing the front No. 2 ultrasonic sensor clip, if the double-sided tape is difficult to remove, heat the adhesive of the front No. 2 ultrasonic sensor clip and front bumper assembly using a heat light.
    1. Heat the front bumper assembly and front No. 2 ultrasonic sensor clip using a heat light.
      WARNING:
      • Do not touch the heat light and heated parts.
      • Touching the heat light may result in burns.
      • Touching heated parts for a long time may result in burns.
      GTY835518Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Heated Part
      *b Heat Light

      Standard

      Item Temperature
      Front Bumper Assembly 20 to 30°C (68 to 86°F)
      Front No. 2 Ultrasonic Sensor Clip
    2. Remove the front No. 2 ultrasonic sensor clip.
      1. except Sport Package:
        GTY966356Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. for Sport Package:
        GTY1232008Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE ULTRASONIC SENSOR CUSHION SET 

    HINT: 

    Only perform this procedure when removing and installing the ultrasonic sensor cushion set.

    1. Remove the ultrasonic sensor cushion set as shown in the illustration.
      GTY1085145Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
scientia non olet · About LEMON Manuals