LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2022 >> LS 500 Base, AWD >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge System - Diagnostics - Introduction (2 Of 2) >> Meter / Gauge System >> Customize Parameters [10/2022 - 10/2023] >> Customize Parameters [10/2022 - 10/2023]

Customize Parameters [10/2022 - 10/2023]

  1. CUSTOMIZE METER / GAUGE SYSTEM 
    1. Customizing with the Techstream.
      1. Connect the Techstream to the DLC3.
      2. Turn the engine switch on (IG).
      3. Turn the Techstream on.
      4. Enter the following menus: Customize Setting / Warning or Display.
      5. Select the setting by referring to the table below.
        NOTE:

        Be sure to record the current value before customizing.

        Warning 

        Tester Display Description Default Setting ECU
        Lane Change Flashing Times Adjust Function to change the lane change flashing time 3 $00:OFF,$01:3,$02:4,$03:5,$04:6,$05:7 Combination meter assembly
        Flasher Sound Volume Adjust Function to change the flasher sound volume Medium $02:Large,$00:Medium,$01:Small Combination meter assembly
        Reverse Buzzer Setting Function to change the reverse warning buzzer type Continual $00:Continual,$01:Single Combination meter assembly

        Display 

        Tester Display Description Default Setting ECU
        ODO Display Time After IG OFF Adjust Function to change the ODO display time after the engine switch is turned off 30s $00:30s,$01:60s,$02:600s,$03:OFF Combination meter assembly
        ECO Drive Indicator Zone Display Function (Meter) Function to change the ECO drive indicator zone display ON $00:OFF,$01:ON Combination meter assembly
    2. Customizing with the multi-information display
      1. Turn the engine switch on (IG).
      2. Select the settings tab on the multi-information display and set the customize settings.
        Display Description Default Setting ECU
        Language Function to change the language on the display English
        • English
        • French
        • Spanish
        		 Combination meter assembly
        Units Function to change the units on the display miles (MPG)
        • km (km/L)
        • km(L/100 km)
        • miles(MPG)
        		 Combination meter assembly
        Speed Meter*2 Function to change the Speedometer on the display Digital
        • Digital
        • Analog
        • Digital and Analog
        		 Combination meter assembly
        Drive Info 1 Function to change the item to be displayed on Drive Info 1
        • Current Fuel Consumption (Bar Display)/Average Fuel Consumption (Mark Display)
        • Total Average Fuel Consumption Between Reset Operations
        • Current Fuel Consumption (Bar Display)/Average Fuel Consumption (Mark Display)
        • Total Average Fuel Consumption Between Reset Operations
        • Average Fuel Consumption After Engine Start-up
        • Average Fuel Consumption After Refueling
        • Total Average Vehicle Speed Between Reset Operations
        • Average Vehicle Speed After Engine Start-up
        • Cruising Range After Engine Start-up
        • Total Elapsed Time Between Reset Operations
        • Elapsed Time After Engine Start-up
        • Cruising Range
        • Blank
        		 Combination meter assembly
        Drive Info 2 Function to change the item to be displayed on Drive Info 1
        • Cruising Range
        • Total Average Vehicle Speed Between Reset Operations
        • Current Fuel Consumption (Bar Display)/Average Fuel Consumption (Mark Display)
        • Total Average Fuel Consumption Between Reset Operations
        • Average Fuel Consumption After Engine Start-up
        • Average Fuel Consumption After Refueling
        • Total Average Vehicle Speed Between Reset Operations
        • Average Vehicle Speed After Engine Start-up
        • Cruising Range After Engine Start-up
        • Total Elapsed Time Between Reset Operations
        • Elapsed Time After Engine Start-up
        • Cruising Range
        • Blank
        		 Combination meter assembly
        Clock 12H/24H setting and clock adjustment / Adjusts the hour / Adjusts the minute/ AM/PM setting - 12H/24H setting and clock adjustment/Adjusts the hour*1/Adjusts the minute*1/AM/PM setting*1 Combination meter assembly
        Pop-Up Display Function to change the pop-up display when selecting a displayed item ON
        • TbT Navigation
        • Telephone
        • Audio Operation
        • Volume Operation
        • Adjust Brightness
        		 Combination meter assembly
        Tachometer Settings Function to change the Tachometer when selecting a displayed item ON (Self-Changing
        • ON (Self-Changing
        • Tachometer(Always)
        • HV Meter(Always)
        		 Combination meter assembly
        REV indicator light Function to turn on/off the REV indicator light OFF ON or OFF Combination meter assembly
        REV Settings Function to change the REV Settings when selecting a displayed item 5000 rpm OFF/2000 to 6400 Combination meter assembly
        ECO mode indicator light Function to turn on/off the ECO driving indicator light ON ON or OFF Combination meter assembly
        EV driving indicator light Function to turn on/off the EV driving indicator light ON ON or OFF Combination meter assembly
        Default Settings Reset the combination meter settings to the default setting - YES or NO Combination meter assembly

        *1: Setting can be changed when clock is malfunctioning or GPS signal is not received

        *2: except F SPORT Model

scientia non olet · About LEMON Manuals