LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2022 >> LC 500h >> Repair and Diagnosis >> External Pages >> Different car >> Section 72 (Audio / Video System - Service Information (Coupe)) >> Instrument Panel Speaker >> Removal [03/2017 - ] >> Procedure

Removal [03/2017 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2024 Lexus LC 500, 2023 Lexus LC 500, 2022 Lexus LC 500, 2021 Lexus LC 500, and 2020 Lexus LC 500. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE FRONT DOOR SCUFF PLATE LH (for Side) 

    Refer to PROCEDURE - Step 10 [03/2017 - 06/2019] , or refer to PROCEDURE - Step 10 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 10 [04/2020 - 05/2023] , or refer to REMOVAL [05/2023 - ]

  2. REMOVE FRONT DOOR OPENING TRIM COVER LH (for Side) 

    Refer to PROCEDURE - Step 12 [03/2017 - 06/2019] , or refer to PROCEDURE - Step 12 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 12 [04/2020 - 05/2023] , or refer to REMOVAL [05/2023 - ]

  3. REMOVE FRONT DOOR NO. 2 OPENING TRIM COVER LH (for Side) 

    Refer to PROCEDURE - Step 14 [03/2017 - 06/2019] , or refer to PROCEDURE - Step 14 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 14 [04/2020 - 05/2023] , or refer to REMOVAL [05/2023 - ]

  4. REMOVE FRONT PILLAR GARNISH LH (for Side) 

    Refer to PROCEDURE - Step 12 [03/2017 - 05/2023] , or refer to REMOVAL [05/2023 - ]

  5. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for Side) 

    Refer to PROCEDURE - Step 35 [03/2017 - 06/2019] , or refer to PROCEDURE - Step 35 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 35 [04/2020 - 05/2023] , or refer to REMOVAL [05/2023 - ]

  6. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY (for Side) 
    NOTE:

    Do not touch the cone part of the speaker.

    1. Remove the 2 screws.
      GTY836650Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the connector and remove the front No. 1 speaker assembly.
  7. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY (for Center) 
    1. Apply protective tape to the areas shown in the illustration to prevent damage in the following procedures.
      GTY825707Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protective tape
    2. Insert the moulding remover B between the instrument safety pad sub-assembly in the position shown in the illustration and create a gap.
      GTY817817Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using moulding remover A in the gap created in the previous procedure, detach the claws.
      GTY817815Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Move the No. 1 speaker opening cover assembly in the direction indicated by the arrow shown in the illustration.
      GTY790065Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    5. Detach the claw in the direction indicated by the arrow shown in the illustration.
      GTY817085Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    6. Detach the claw in the direction indicated by the arrow shown in the illustration and remove the No. 1 speaker opening cover assembly.
      GTY823018Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  8. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for Center) 
    NOTE:

    Do not touch the cone part of the speaker.

    1. Remove the 2 screws.
      GTY836661Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the connector and remove the front No. 2 speaker assembly.
scientia non olet · About LEMON Manuals