LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2022 >> LC 500h >> Repair and Diagnosis >> External Pages >> Different car >> Section 136 (Suspension System (Front) - Service Information (Coupe)) >> Front Upper Suspension Arm >> Installation [03/2017 - 05/2023] >> Procedure

Installation [03/2017 - 05/2023]: Procedure

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2024 Lexus LC 500, 2023 Lexus LC 500, 2022 Lexus LC 500, 2021 Lexus LC 500, and 2020 Lexus LC 500. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL FRONT UPPER NO. 1 SUSPENSION ARM ASSEMBLY LH 
    1. Temporarily install the front upper No. 1 suspension arm assembly LH to the front upper No. 1 arm bracket LH with the bolt and nut.

      HINT: 

      When installing the front upper No. 1 suspension arm assembly LH, temporarily tighten the bolts at the position shown in the illustration.

      GTY777131Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 7.25°
      *b 26.3 mm (1.04 in.)
      *c 225.6 mm (8.88 in.)
    2. Fully tighten the bolt.

      Torque: 45 N.m (459 kgf/cm, 33 ft.lbf) 

  2. INSTALL FRONT UPPER NO. 2 SUSPENSION ARM ASSEMBLY LH 
    1. Temporarily install the front upper No. 2 suspension arm assembly LH to the front upper No. 2 arm bracket LH with the bolt and nut.

      HINT: 

      When installing the front upper No. 2 suspension arm assembly LH, temporarily tighten the bolts at the position shown in the illustration.

      GTY791006Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 9.15°
      *b 21 mm (0.827 in.)
      *c 209.3 mm (8.24 in.)
    2. Fully tighten the bolt.

      Torque: 45 N.m (459 kgf/cm, 33 ft.lbf) 

  3. INSTALL FRONT UPPER NO. 1 ARM BRACKET LH 
    1. Install the front upper No. 1 arm bracket LH with the 3 bolts.

      Torque: 40 N.m (408 kgf/cm, 30 ft.lbf) 

      GTY813830Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL FRONT UPPER NO. 2 ARM BRACKET LH 
    1. Install the front upper No. 2 arm bracket LH with the 3 bolts.

      Torque: 40 N.m (408 kgf/cm, 30 ft.lbf) 

      GTY813829Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. CONNECT STEERING KNUCKLE ASSEMBLY LH 
    1. Install the steering knuckle assembly LH to the front upper No. 1 suspension arm assembly LH and front upper No. 2 suspension arm assembly LH with the 2 nuts.

      Torque: 60 N.m (612 kgf/cm, 44 ft.lbf) 

      GTY835763Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install 2 new clips.
      NOTE:

      Further tighten the nut up to 60° if the holes for the clip are not aligned.

  6. INSTALL FRONT WHEEL 

    Refer to INSTALLATION [03/2017 - 05/2023]

  7. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT 

    Refer to ADJUSTMENT [03/2017 - 04/2020] , or refer to ADJUSTMENT [04/2020 - 05/2023]

  8. ADJUST HEADLIGHT AIMING 

    Refer to ADJUSTMENT [03/2017 - ]

  9. ADJUST REAR TELEVISION CAMERA ASSEMBLY OPTICAL AXIS 

    Refer to CALIBRATION [03/2017 - 05/2023]

scientia non olet · About LEMON Manuals