LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2022 >> LC 500 2D Convertible >> Repair and Diagnosis >> Body & Frame >> Exterior Body Panels >> Exterior Panels / Trim - Service Information (Convertible) (2 Of 2) >> Rocker Panel Moulding >> Disassembly [07/2020 - ] >> Procedure

Disassembly [07/2020 - ]: Procedure

  1. REMOVE NO. 1 SIDE MUDGUARD PROTECTOR 

    HINT: 

    When removing the No. 1 side mudguard protector, if the double-sided tape is difficult to remove, heat the adhesive of the No. 1 side mudguard protector and body rocker panel moulding assembly LH using a heat light.

    Standard Value

    Part Temperature
    Body Rocker Panel Moulding Assembly LH 20 to 30°C (68 to 86°F)
    No. 1 Side Mudguard Protector
    WARNING:
    • Do not touch the heat light and heated parts.
    • Touching the heat light may result in burns.
    • Touching heated parts for a long time may result in burns.
    GTY749838Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Heated Part
    *b Heat Light
    NOTE:

    Do not heat No. 1 side mudguard protector excessively.

    1. Remove the 2 No. 1 side mudguard protectors.
      GTY952894Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. REMOVE NO. 2 SIDE MUDGUARD PROTECTOR 

    HINT: 

    When removing the No. 2 side mudguard protector, if the double-sided tape is difficult to remove, heat the adhesive of the No. 2 side mudguard protector and body rocker panel moulding assembly LH using a heat light.

    Standard Value

    Part Temperature
    Body Rocker Panel Moulding Assembly LH 20 to 30°C (68 to 86°F)
    No. 2 Side Mudguard Protector
    WARNING:
    • Do not touch the heat light and heated parts.
    • Touching the heat light may result in burns.
    • Touching heated parts for a long time may result in burns.
    GTY749838Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Heated Part
    *b Heat Light
    NOTE:

    Do not heat No. 2 side mudguard protector excessively.

    1. Remove the 2 No. 2 side mudguard protectors.
      GTY953851Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE REAR BUMPER PAD 

    HINT: 

    When removing the rear bumper pad, if the double-sided tape is difficult to remove, heat the adhesive of the rear bumper pad and body rocker panel moulding assembly LH using a heat light.

    Standard Value

    Part Temperature
    Body Rocker Panel Moulding Assembly LH 20 to 30°C (68 to 86°F)
    Rear Bumper Pad
    WARNING:
    • Do not touch the heat light and heated parts.
    • Touching the heat light may result in burns.
    • Touching heated parts for a long time may result in burns.
    GTY749838Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Heated Part
    *b Heat Light
    NOTE:

    Do not heat rear bumper pad excessively.

    1. Remove the rear bumper pad.
      GTY800091Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE NO. 3 ROCKER PANEL MOULDING PROTECTOR 

    HINT: 

    When removing the No. 3 rocker panel moulding protector, if the double-sided tape is difficult to remove, heat the adhesive of the No. 3 rocker panel moulding protector and body rocker panel moulding assembly LH using a heat light.

    Standard Value

    Part Temperature
    Body Rocker Panel Moulding Assembly LH 20 to 30°C (68 to 86°F)
    No. 3 Rocker Panel Moulding Protector
    WARNING:
    • Do not touch the heat light and heated parts.
    • Touching the heat light may result in burns.
    • Touching heated parts for a long time may result in burns.
    GTY749838Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Heated Part
    *b Heat Light
    NOTE:

    Do not heat No. 3 rocker panel moulding protector excessively.

    1. Remove the No. 3 rocker panel moulding protector.
      GTY953030Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE NO. 4 ROCKER PANEL MOULDING PROTECTOR 

    HINT: 

    When removing the No. 4 rocker panel moulding protector, if the double-sided tape is difficult to remove, heat the adhesive of the No. 4 rocker panel moulding protector and body rocker panel moulding assembly LH using a heat light.

    Standard Value

    Part Temperature
    Body Rocker Panel Moulding Assembly LH 20 to 30°C (68 to 86°F)
    No. 4 Rocker Panel Moulding Protector
    WARNING:
    • Do not touch the heat light and heated parts.
    • Touching the heat light may result in burns.
    • Touching heated parts for a long time may result in burns.
    GTY749838Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Heated Part
    *b Heat Light
    NOTE:

    Do not heat No. 4 rocker panel moulding protector excessively.

    1. Remove the No. 4 rocker panel moulding protector.
      GTY953624Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE NO. 2 ROCKER PANEL MOULDING PROTECTOR 

    HINT: 

    When removing the No. 2 rocker panel moulding protector, if the double-sided tape is difficult to remove, heat the adhesive of the No. 2 rocker panel moulding protector and body rocker panel moulding assembly LH using a heat light.

    Standard Value

    Part Temperature
    Body Rocker Panel Moulding Assembly LH 20 to 30°C (68 to 86°F)
    No. 2 Rocker Panel Moulding Protector
    WARNING:
    • Do not touch the heat light and heated parts.
    • Touching the heat light may result in burns.
    • Touching heated parts for a long time may result in burns.
    GTY749838Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Heated Part
    *b Heat Light
    NOTE:

    Do not heat No. 2 rocker panel moulding protector excessively.

    1. Remove the No. 2 rocker panel moulding protector.
      GTY953621Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE NO. 1 ROCKER PANEL MOULDING PROTECTOR 

    HINT: 

    When removing the No. 1 rocker panel moulding protector, if the double-sided tape is difficult to remove, heat the adhesive of the No. 1 rocker panel moulding protector and body rocker panel moulding assembly LH using a heat light.

    Standard Value

    Part Temperature
    Body Rocker Panel Moulding Assembly LH 20 to 30°C (68 to 86°F)
    No. 1 Rocker Panel Moulding Protector
    WARNING:
    • Do not touch the heat light and heated parts.
    • Touching the heat light may result in burns.
    • Touching heated parts for a long time may result in burns.
    GTY749838Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Heated Part
    *b Heat Light
    NOTE:

    Do not heat No. 1 rocker panel moulding protector excessively.

    1. Remove the No. 1 rocker panel moulding protector.
      GTY953618Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE NO. 6 ROCKER PANEL MOULDING PROTECTOR 

    HINT: 

    When removing the No. 6 rocker panel moulding protector, if the double-sided tape is difficult to remove, heat the adhesive of the No. 6 rocker panel moulding protector and body rocker panel moulding assembly LH using a heat light.

    Standard Value

    Part Temperature
    Body Rocker Panel Moulding Assembly LH 20 to 30°C (68 to 86°F)
    No. 6 Rocker Panel Moulding Protector
    WARNING:
    • Do not touch the heat light and heated parts.
    • Touching the heat light may result in burns.
    • Touching heated parts for a long time may result in burns.
    GTY749838Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Heated Part
    *b Heat Light
    NOTE:

    Do not heat No. 6 rocker panel moulding protector excessively.

    1. Remove the No. 6 rocker panel moulding protector.
      GTY789279Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals