LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2022 >> ES 350 Base >> Repair and Diagnosis >> Brakes >> Mechanical - Hydraulic >> Electronically Controlled Brake System (Except Hybrid) - Diagnostic Codes (2 Of 4) >> ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) >> DTC C0512-1F: Right Rear Wheel Speed Sensor Circuit Intermittent [08/2020 - ] >> Procedure

DTC C0512-1F: Right Rear Wheel Speed Sensor Circuit Intermittent [08/2020 - ]: Procedure

  1. CHECK VEHICLE 
    1. Check the vehicle specification.

      Result

      Result Proceed to
      for 2WD A
      for AWD B

    Result: 

    A 

    REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH. Refer to  REMOVAL [06/2018 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

    Result: 

    B 

    See step  2

  2. CHECK REAR SPEED SENSOR RH (CHECK FOR FOREIGN MATTER) 
    1. Remove the rear speed sensor RH.

      Refer to REMOVAL [08/2020 - ]

    2. Check the rear speed sensor RH.

      OK

      The rear speed sensor RH tip is free of oil and foreign matter.

      HINT: 

      If foreign matter of 1 mm x 1 mm or more is adhered to the rear speed sensor RH, this DTC may be stored.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  8

    Result: 

    OK 

    See step  3

  3. CHECK REAR SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER) 
    1. Remove the component with the rear speed sensor rotor RH.

      Refer to REMOVAL [08/2020 - ]

    2. Check the rear speed sensor rotor RH.

      OK

      The rear speed sensor rotor RH is free of oil and foreign matter.

      HINT: 

      If foreign matter of 1 mm x 1 mm or more is adhered to the rear speed sensor rotor RH, this DTC may be stored.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REAR SPEED SENSOR RH AND REAR AXLE HUB AND BEARING ASSEMBLY RH 

    for rear speed sensor RH: Refer to REMOVAL [08/2020 - ]

    for rear speed sensor rotor RH (rear axle hub and bearing assembly RH): Refer to REMOVAL [08/2020 - ]

    Result: 

    NG 

    See step  4

  4. CLEAN REAR SPEED SENSOR ROTOR RH 
    1. Clean the rear speed sensor rotor RH.
      NOTE:

      Do not use parts cleaner when cleaning the rear speed sensor rotor RH.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  5

  5. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

      Chassis > Brake/EPB > Clear DTCs 

    4. Press the DTC clear button.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  6

  6. PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Using the Techstream, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.

      Refer to TEST MODE PROCEDURE [08/2020 - ]

      Chassis > Brake/EPB > Utility 

      Tester Display
      Signal Check

      OK

      Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SPEED SENSOR RH AND REAR AXLE HUB AND BEARING ASSEMBLY RH 

    for rear speed sensor RH: Refer to REMOVAL [08/2020 - ]

    for rear speed sensor rotor RH (rear axle hub and bearing assembly RH): Refer to REMOVAL [08/2020 - ]

    Result: 

    OK 

    See step  7

  7. RECONFIRM DTC 
    1. Connect the Techstream to the DLC3.
    2. Start the engine.
    3. Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
    4. Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

      Chassis > Brake/EPB > Trouble Codes 

    5. Check if the same DTC is output.

      Result

      Result Proceed to
      C0512-1F is not output A
      C0512-1F is output B

    Result: 

    A 

    END 

    Result: 

    B 

    REPLACE REAR SPEED SENSOR RH AND REAR AXLE HUB AND BEARING ASSEMBLY RH 

    for rear speed sensor RH: Refer to REMOVAL [08/2020 - ]

    for rear speed sensor rotor RH (rear axle hub and bearing assembly RH): Refer to REMOVAL [08/2020 - ]

  8. CLEAN REAR SPEED SENSOR RH 
    1. Clean the rear speed sensor RH.
      NOTE:

      When cleaning the rear speed sensor RH, make sure to clean the installation hole before installation.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  9

  9. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

      Chassis > Brake/EPB > Clear DTCs 

    4. Press the DTC clear button.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  10

  10. PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Using the Techstream, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.

      Refer to TEST MODE PROCEDURE [08/2020 - ]

      Chassis > Brake/EPB > Utility 

      Tester Display
      Signal Check

      OK

      Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  3

    Result: 

    OK 

    See step  11

  11. RECONFIRM DTC 
    1. Connect the Techstream to the DLC3.
    2. Start the engine.
    3. Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
    4. Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

      Chassis > Brake/EPB > Trouble Codes 

    5. Check if the same DTC is output.

      Result

      Result Proceed to
      C0512-1F is not output A
      C0512-1F is output B

    Result: 

    A 

    END 

    Result: 

    B 

    See step  3

scientia non olet · About LEMON Manuals