LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2022 >> ES 300h Base >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge / Display - Service Information >> HEADUP Display >> Reassembly [06/2018 - ] >> Procedure

Reassembly [06/2018 - ]: Procedure

  1. PRECAUTION 
    1. Static electricity countermeasures SST
      1. SST: Desktop anti-static mat set
        GTY798036Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        • SST: 09890-47010 
          1. 09891-04010
          2. 09891-04020
          3. 09891-04030
          4. 09891-04040
        • Anti-static mat
        • Wristband
        • Wristband connection wire (No. 1 grounding wire)
        • Ground connection wire (No. 2 grounding wire)
    2. Precautions during replacement
      1. Precautions during procedures:
        1. Before performing any procedures, touch an unpainted metal part or ground bolt of the vehicle to eliminate any static electricity.
        2. To prevent damage to electrical equipment, disconnect the battery power supply before installing and removing electrical equipment.
        3. Never touch the electronic parts of a printed wire board or the pins of an integrated circuit.
        4. When performing procedures, do not allow clothing to come near or contact parts.
      2. Wear SST (wristband) firmly on your wrist.
        GTY798036Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Connect SST (No. 2 grounding wire) and SST (anti-static mat) to an appropriate grounding point in the workspace and on the work table.

        HINT: 

        When working inside the vehicle: 

        Connect SST (No. 2 grounding wire) to an unpainted metal part or ground bolt, etc.

        GTY800309Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      4. Connect SST (No. 1 grounding wire), SST (wristband) and SST (anti-static mat).
      5. Always place the meter mirror sub-assembly and its components on SST (anti-static mat).
  2. INSTALL NO. 1 COMBINATION METER MIRROR PLATE 
    NOTE:
    • Prevention of static electricity is required during this procedure.
    • Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).
    1. Engage the 2 guides as shown in the illustration.
      GTY787589Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Install in this Direction
    2. Install the screw.
      GTY798415Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Engage the guide.
      GTY798413Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Make sure that the wire harness and guide are engaged as shown in the illustration. Failure to do so may damage the wire harness.

      GTY798416Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Engage the 2 claws as shown in the illustration.
      GTY789182Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction (1)
      Install in this Direction (2)
      NOTE:

      Do not forcibly pull the wire harness as it may become damaged.

    5. Install the No. 1 combination meter mirror plate with the 7 screws.
      GTY832360Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL NO. 1 COMBINATION SPEEDOMETER CUSHION 
    1. Clean the meter mirror sub-assembly surface.
      1. Remove any remaining double-sided tape from the meter mirror sub-assembly.
      2. Wipe off any tape adhesive residue with cleaner.
    2. Remove the release paper from a new No. 1 combination speedometer cushion.

      HINT: 

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. Install the No. 1 combination speedometer cushion as shown in the illustration.
      GTY800121Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Outline
      *b Edge of Curved Surface
scientia non olet · About LEMON Manuals