LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2021 >> UX 200 Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Infotainment >> Navigation System (Diagnostic Codes) (1 Of 2) >> Navigation System >> DTC B1323: Lost Communication with Haptic Device; DTC B1324: Lost Communication with Meter; DTC B1325: Lost Communication with HUD; DTC B1326: Lost Communication with Clock Device (Local-CAN) [10/2019 - 07/2022] >> Procedure

DTC B1323: Lost Communication with Haptic Device; DTC B1324: Lost Communication with Meter; DTC B1325: Lost Communication with HUD; DTC B1326: Lost Communication with Clock Device (Local-CAN) [10/2019 - 07/2022]: Procedure

  1. CHECK DTC 
    1. Check for DTCs.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTC B1323, B1324, B1325 and B1326 are not output A
      DTC B1323, B1324, B1325 and B1326 are output B
      DTC B1323 is output C
      DTC B1324 is output D
      DTC B1325 is output E
      DTC B1326 is output F

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2018 - ] 

    Result: 

    C 

    See step  17

    Result: 

    D 

    See step  19

    Result: 

    E 

    See step  21

    Result: 

    F 

    See step  23

    Result: 

    B 

    See step  2

  2. CHECK LOCAL BUS 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F92-2 - F92-13 Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

      Result

      Result Proceed to
      OK A
      NG (Below 54 Ω) B
      NG (70 Ω or higher) C

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2018 - ] 

    Result: 

    C 

    See step  13

    Result: 

    B 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - RADIO RECEIVER ASSEMBLY) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F92 No. 5 CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F92-2 - F92-13 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  12

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY)) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F91 No. 5 CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F91-11 - F91-22 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  11

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F91 No. 5 CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F91-8 - F91-19 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  10

    Result: 

    OK 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CLOCK ASSEMBLY) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F91 No. 5 CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F91-10 - F91-21 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  9

    Result: 

    OK 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F92 No. 5 CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F92-3 - F92-14 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 5 CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 5 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F25 headup display (meter mirror sub-assembly) connector.
    3. Connect the F92 No. 5 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F25-14 (TX+) - F25-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY). Refer to  REMOVAL [10/2018 - 07/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  9. CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F29 clock assembly connector.
    3. Connect the F91 No. 5 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F29-5 (TX+1) - F29-6 (TX-1) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CLOCK ASSEMBLY. Refer to  REMOVAL [10/2018 - 07/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  10. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F23 combination meter assembly connector.
    3. Connect the F91 No. 5 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F23-8 (TX+) - F23-7 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [10/2018 - 07/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  11. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 5 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F32 remote touch (remote operation controller assembly) connector.
    3. Connect the F91 No. 5 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F32-9 (MO+) - F32-8 (MO-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY). Refer to  REMOVAL [10/2018 - 07/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  12. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F2 radio receiver assembly connector.
    3. Connect the F92 No. 5 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F2-5 (CNH1) - F2-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [10/2019 - 07/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  13. CHECK HARNESS AND CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - RADIO RECEIVER ASSEMBLY) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F92 No. 5 CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F92-2 - F92-13 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  16

    Result: 

    OK 

    See step  14

  14. CHECK HARNESS AND CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY)) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F91 No. 5 CAN junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F91-11 - F91-22 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 5 CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  15

  15. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 5 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F32 remote touch (remote operation controller assembly) connector.
    3. Connect the F91 No. 5 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F32-9 (MO+) - F32-8 (MO-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY). Refer to  REMOVAL [10/2018 - 07/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  16. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F2 radio receiver assembly connector.
    3. Connect the F92 No. 5 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F2-5 (CNH1) - F2-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [10/2019 - 07/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  17. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) POWER SOURCE) 
    1. Disconnect the remote touch (remote operation controller assembly) connector.
      GTY809000Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Remote Touch (Remote Operation Controller Assembly))
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F32-10 (GND) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      F32-1 (+B) - Body ground Ignition switch off 11 to 14 V
      F32-6 (ACC) - Body ground Ignition switch ACC 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  18

  18. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 5 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F32 remote touch (remote operation controller assembly) connector.
    3. Connect the F91 No. 5 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F32-9 (MO+) - F32-8 (MO-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY). Refer to  REMOVAL [10/2018 - 07/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  19. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE) 
    1. Disconnect the combination meter assembly connector.
      GTY825347Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Combination Meter Assembly)
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F23-31 (ES) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      F23-22 (B) - Body ground Ignition switch off 11 to 14 V
      F23-21 (IG+) - Body ground Ignition switch ON 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  20

  20. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F23 combination meter assembly connector.
    3. Connect the F91 No. 5 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F23-8 (TX+) - F23-7 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [10/2018 - 07/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  21. CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE) 
    1. Disconnect the headup display (meter mirror sub-assembly) connector.
      GTY819264Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Headup Display (Meter Mirror Sub-assembly)
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F25-4 (ES) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      F25-2 (B) - Body ground Ignition switch off 11 to 14 V
      F25-1 (IG) - Body ground Ignition switch ON 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  22

  22. CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 5 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F25 headup display (meter mirror sub-assembly) connector.
    3. Connect the F92 No. 5 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F25-14 (TX+) - F25-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY). Refer to  REMOVAL [10/2018 - 07/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  23. CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY POWER SOURCE) 
    1. Disconnect the clock assembly connector.
      GTY796948Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Clock Assembly)
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F29-7 (E) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      F29-1 (B) - Body ground Ignition switch off 11 to 14 V
      F29-2 (ACC) - Body ground Ignition switch ACC 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  24

  24. CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the F29 clock assembly connector.
    3. Connect the F91 No. 5 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F29-5 (TX+1) - F29-6 (TX-1) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CLOCK ASSEMBLY. Refer to  REMOVAL [10/2018 - 07/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals