LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2021 >> NX 300 Base, FWD >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge / Display - Service Information >> Clock >> Removal [10/2014 - 09/2017] >> Procedure

Removal [10/2014 - 09/2017]: Procedure

  1. PRECAUTION 
    NOTE:
    • Be sure to read Precaution thoroughly before servicing.

      Refer to PRECAUTION [10/2014 - 09/2017] 

    • Handle components indoors as much as possible to prevent foreign matter from entering and adhering to clock assembly components.
    • When installing components, make sure that the heater control cable sub-assembly is not pinched or pulled.
  2. REMOVE CONSOLE ARMREST ASSEMBLY 

    Refer to PROCEDURE - Step 5

  3. REMOVE UPPER REAR CONSOLE PANEL 

    Refer to PROCEDURE - Step 6

  4. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH 

    Refer to PROCEDURE - Step 7

  5. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH 

    Refer to PROCEDURE - Step 8

  6. REMOVE INSTRUMENT SIDE PANEL LH 

    Refer to PROCEDURE - Step 9

  7. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 10

  8. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 11

  9. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL 

    Refer to PROCEDURE - Step 12

  10. REMOVE NO. 1 SWITCH HOLE BASE 

    Refer to PROCEDURE - Step 13

  11. REMOVE INSTRUMENT SIDE PANEL RH 

    Refer to PROCEDURE - Step 14

  12. REMOVE NO. 2 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 15

  13. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY 

    Refer to PROCEDURE - Step 16

  14. REMOVE AIR CONDITIONING CONTROL ASSEMBLY 
    1. Pull the air conditioning control assembly in the direction indicated by the arrows shown in the illustration to detach the 6 clips.
      GTY514076Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the connectors and remove the air conditioning control assembly.
  15. REMOVE CLOCK ASSEMBLY 
    NOTE:
    • Prevention of static electricity is required during this procedure.
    • Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).
    • SST: 09890-47010 
      1. 09891-04010
      2. 09891-04020
      3. 09891-04030
      4. 09891-04040
    1. Remove the 6 screws and cover.
      GTY960866Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. GTY960869Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Release the connector lock and disconnect the heater control cable sub-assembly.

    3. Insert a thin-bladed screwdriver with its tip wrapped with protective tape at the position shown in the illustration, detach the 2 claws and remove the clock assembly.
      GTY961258Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Rib
      Protective Tape
      NOTE:

      Do not grab the rib and detach the claw.

  16. REMOVE HEATER CONTROL CABLE SUB-ASSEMBLY 
    NOTE:
    • Prevention of static electricity is required during this procedure.
    • Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

    HINT: 

    Perform this procedure only when replacing the heater control cable sub-assembly.

    • SST: 09890-47010 
      1. 09891-04010
      2. 09891-04020
      3. 09891-04030
      4. 09891-04040
    1. GTY960867Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Release the connector lock and remove the heater control cable sub-assembly.

scientia non olet · About LEMON Manuals