Problem Symptoms Table [05/2018 - 05/2019]
NOTE:
- When replacing the combination meter assembly, make sure to replace it with a new one.
- w/ Lane Departure Alert System:
When replacing the lane departure warning camera, make sure to replace it with a new one.
- w/ Pre-collision System:
When replacing the driving support ECU assembly, make sure to replace it with a new one.
- Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).
- If the main body ECU (multiplex network body ECU) is replaced, refer to registration.
- After replacing the radio receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptom are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
METER GAUGE
| Symptom | Suspected Area | Link |
|---|---|---|
| Speedometer malfunction | Refer to "Speedometer Malfunction" | Refer to Speedometer Malfunction [10/2014 - 05/2019] |
| Tachometer malfunction | Refer to "Tachometer Malfunction" | Refer to Tachometer Malfunction [10/2014 - ] |
| Fuel receiver gauge malfunction (Fuel receiver gauge is currently malfunctioning, or was malfunctioning in the past) |
Refer to "Fuel Receiver Gauge Display Malfunction" | Refer to Fuel Receiver Gauge Display Malfunction [10/2014 - 05/2019] |
| Engine coolant temperature receiver gauge malfunction | Refer to "Engine Coolant Temperature Receiver Gauge Malfunction" | Refer to Engine Coolant Temperature Receiver Gauge Malfunction [10/2014 - ] |
WARNING LIGHT OR INDICATOR LIGHT
| Symptom | Suspected Area | Link |
|---|---|---|
| Turn indicator light does not come on (Turn signal light operates normally) | Perform Active Test [Turn Signal (Left) Indicator, Turn Signal (Right) Indicator] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] |
| Read the Data List [Turn Signal Switch (Right), Turn Signal Switch (Left)] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Front fog indicator light does not come on (Front fog light operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Perform Active Test [Indicat. Lamp Fr FOG] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| High beam indicator light does not come on (High beam headlight operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Perform Active Test [Indicat. Lamp Beam] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| Automatic high beam indicator light does not come on (w/ Automatic High Beam System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Automatic High Beam Indicator] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Automatic high beam system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Taillight indicator light does not come on (Taillight operates normally) (with km/h units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Perform Active Test [Indicat. Lamp Tail] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Headlight indicator light does not come on (Headlight operates normally) (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Perform Active Test [Indicat. Lamp Head] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driver side seat belt warning light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Perform Active Test [Driver Side Seat Belt] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Proceed to "Driver Side Seat Belt Warning Light does not Operate" | Refer to Driver Side Seat Belt Warning Light does not Operate [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Front passenger side seat belt warning light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Proceed to "Front Passenger Side Seat Belt Warning Light Malfunction" | Refer to Front Passenger Side Seat Belt Warning Light Malfunction [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| SRS warning light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Indicat. Lamp Airbag] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Proceed to "SRS Warning Light Remains ON" | Refer to SRS Warning Light Remains ON [10/2014 - 05/2019] | |
| Proceed to "SRS Warning Light does not Come ON" | Refer to SRS Warning Light does not Come ON [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Master warning light (Other systems operate normally) | Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] |
| Perform Active Test [Master Warning] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| MIL (Malfunction indicator lamp) malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Check Engine Indicator] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Proceed to "MIL Circuit" | Refer to MIL Circuit [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| EPS warning light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Indicat. EPS] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Proceed to "Power Steering Warning Light Circuit" (for Manual Tilt and Manual Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Proceed to "Power Steering Warning Light Circuit" (for Power Tilt and Power Telescopic Steering Column) | Refer to Power Steering Warning Light Circuit [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake warning light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Indicat. Lamp Brake] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Proceed to "Brake Warning Light Remains ON" | Refer to Brake Warning Light Remains ON [09/2017 - 05/2019] | |
| Proceed to "Brake Warning Light does not Come ON" | Refer to Brake Warning Light does not Come ON [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Cruise indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Proceed to "Cruise Main Indicator Light Circuit" | Refer to Cruise Main Indicator Light Circuit [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| SET indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Proceed to "Cruise SET Indicator Light Circuit" (w/o Dynamic Radar Cruise Control System) | Refer to Cruise SET Indicator Light Circuit [09/2017 - 05/2019] | |
| Proceed to "Cruise SET Indicator Light Circuit" (w/ Dynamic Radar Cruise Control System) | Refer to Cruise SET Indicator Light Circuit [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Radar cruise indicator light does not come on (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Proceed to "Cruise Main Indicator Light Circuit" | Refer to Cruise Main Indicator Light Circuit [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure alert indicator light does not come on (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Proceed to "Indicator Circuit" | Refer to Indicator Circuit [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Steering indicator light does not come on (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| Tire pressure warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Indicat. Tire Pressure Warning System] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Proceed to "Tire Pressure Warning Light Circuit" | Refer to Tire Pressure Warning Light Circuit [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Fuel level warning light does not come on (Fuel receiver gauge operates normally) | Perform Active Test [Indicat. Lamp Fuel] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ABS warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Indicat. Lamp ABS] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Proceed to "ABS Warning Light Remains ON" | Refer to ABS Warning Light Remains ON [10/2014 - 05/2019] | |
| Proceed to "ABS Warning Light does not Come ON" | Refer to ABS Warning Light does not Come ON [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Slip indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Indicat. Lamp Slip] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Proceed to "Slip Indicator Light Remains ON" | Refer to Slip Indicator Light Remains ON [10/2014 - 05/2019] | |
| Proceed to "Slip Indicator Light does not Come ON" | Refer to Slip Indicator Light does not Come ON [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| VSC OFF indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Indicat. VSC OFF] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Proceed to "VSC OFF Switch Circuit" | Refer to VSC OFF Switch Circuit [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| EPB* warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Perform Active Test [Indicat. Park] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| PCS OFF indicator light malfunction (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Indicat. Precrash] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Pre-collision System | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| Clearance sonar indicator light does not come on (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Perform Active Test [Indicat. INTUITIVE P/A LCD] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Intuitive parking assist system (w/ Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Intuitive parking assist system (w/o Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| ICS OFF indicator light malfunction (w/ Intelligent Clearance Sonar System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Intelligent clearance sonar system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| Eco mode indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Eco driving indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Indicat. ECONO] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Sport mode indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Absorber control ECU (w/ Adaptive Variable Suspension System) | Refer to REMOVAL [10/2014 - 05/2019] | |
| Brake hold standby indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Indicat. Brake Hold] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Proceed to "Brake Hold Standby Indicator Light Circuit" | Refer to Brake Hold Standby Indicator Light Circuit [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake hold operated indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Indicat. Hold] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Proceed to "Brake Hold Operated Indicator Light Circuit" | Refer to Brake Hold Operated Indicator Light Circuit [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| AWD indicator light does not come on (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - 05/2019] | |
| Perform Active Test [Indicat. Ctr DIFF LOCK] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] | |
| Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] |
MULTI-INFORMATION DISPLAY
| Symptom | Suspected Area | Link |
|---|---|---|
| "Opening" display malfunction | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Each door ajar" display malfunction (Door courtesy switch, back door courtesy switch or hood courtesy switch is normal) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Outside temp" display malfunction*A | Proceed to "Ambient Temperature Display System" | Refer to Ambient Temperature Display System [09/2017 - 05/2019] |
| Icy street warning display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Air conditioning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Air conditioning amplifier assembly | Refer to REMOVAL [09/2017 - ] | |
| "Windshield Washer Fluid Low" display malfunction | Proceed to "Washer Fluid Level Warning Switch Circuit" | Refer to Washer Fluid Level Warning Switch Circuit [10/2014 - ] |
| "Current fuel consumption" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Average fuel consumption (After refuel)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Average fuel consumption (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Average fuel consumption (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Average speed (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Average speed (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Elapsed time (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Elapsed time (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Distance (Range)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Distance (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Eco driving indicator zone" display malfunction (for F-Sport Seat Type) | SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Boost gauge/oil pressure gauge/oil level indicator" display malfunction (for F-Sport Seat Type) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "G monitor" display malfunction (for F-Sport Seat Type) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| Tire pressure display malfunction | Tire pressure warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| "Navigation tab" display malfunction | Navigation system (w/ Navigation System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] |
| Audio and visual system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Radio receiver assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Audio tab" display malfunction | Navigation system (w/ Navigation System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] |
| Audio and visual system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Radio receiver assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Radar cruise control / lane departure alert displayed tab" display malfunction (w/ Dynamic Radar Cruise Control System or Lane Departure Alert System) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Message tab" display malfunction | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Setting tab" display malfunction | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Shift selector" display malfunction | Perform Active Test [A/T Indicator Operation 1, A/T Indicator Operation 2, A/T Indicator Operation 3] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "SPORT indicator" display malfunction | SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Adaptive variable suspension system (w/ Adaptive Variable Suspension System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Absorber control ECU (w/ Adaptive Variable Suspension System) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "SPORT S indicator" display malfunction | SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Adaptive variable suspension system (w/ Adaptive Variable Suspension System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Absorber control ECU (w/ Adaptive Variable Suspension System) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "SPORT S+ indicator" display malfunction | SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Adaptive variable suspension system (w/ Adaptive Variable Suspension System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Absorber control ECU (w/ Adaptive Variable Suspension System) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Fuel Low" display malfunction (Fuel receiver gauge operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "AWD TEST MODE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "CDY-2" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "CDY-4" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "AWD System Malfunction 2WD Mode Engaged Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "AWD System Overheated 2WD Mode Engaged" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "AWD System Overheated Switching to 2WD Mode" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Push and Hold Engine Switch for Emergency Stop" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Shift to N and Press Engine Switch to Restart" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Power Turned Off to Save Battery" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Key Not Detected Check Key Location" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Smart Access System Malfunction See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Turn Off Vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Key Left inside Vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Depress Brake and Then Touch Key to Engine Switch" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Depress Brake and Then Start Engine" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Shift to P Before Exiting Vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Key Battery Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "IGNITION ON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Steering Wheel Lock Press Engine Switch while Turning Wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Steering lock system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Engine Stopped Shift to P" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Engine Stopped Stop in a Safe Place" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Switch to Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Intelligent clearance sonar system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Object Detected Acceleration Reduced" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Intelligent clearance sonar system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Accelerator Stuck Depress Brake to Stop" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Release Accelerator" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Check Engine Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Check Engine Reduced Engine Power Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Engine Coolant Temp High Stop in a Safe Place See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Engine Oil Level low Add or Replace" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Harness or connector | - |
| Engine oil level sensor | Refer to INSPECTION [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| "Charging System Malfunction See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Charging system | Refer to PROBLEM SYMPTOMS TABLE [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Drive-Start Control Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Brake Override Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Accelerator and Brake Pedals Depressed Simultaneously" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Low Oil Pressure Stop in a Safe Place See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Oil Maintenance Required Soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Maintenance Required Soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Injector Maintenance Required Soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Oil Maintenance Required Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Maintenance Required Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Injector Maintenance Required Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Transmission Fluid Temp High See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Automatic transaxle system (for U661E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Automatic transaxle system (for U661F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Antilock Brake System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Braking Power Low Stop in a Safe Place See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Traction Control Turned Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Brake Hold Fault Depress Brake to Deactivate Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Brake Hold Warning Depress Brake on Slope" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Brake Hold Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Brake Hold Less Effective during Icy Conditions" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Brake Hold Active Depress Brake and Switch to Deactivate" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Brake Hold Unavailable Driver Door Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Brake Hold Unavailable Driver Seat Belt Unbuckled" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Brake Hold Unavailable Hood or Trunk Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Depress Brake to Maintain Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Close Driver Door to Maintain Brake Hold " message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Fasten Driver Seat Belt to Maintain Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Braking Power Low Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Release Parking Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Vehicle May Roll Shift to P" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Release Parking Brake while Depressing Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Parking Brake Overheated Parking Brake Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Parking Brake Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Electronic Parking Brake Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Parking Brake Activated Release Before Driving" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Brake Hold Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Brake Hold Deactivted" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Automatic Mode On Shift Operation Sets or Releases Parking Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Automatic Mode Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Power Steering Malfunction Steering Power Low Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Power steering system (for Manual Tilt and Manual Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Power steering system (for Power Tilt and Power Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Power steering ECU assembly (for Manual Tilt and Manual Telescopic Steering Column) | Refer to REMOVAL [10/2014 - ] | |
| Power steering ECU assembly (for Power Tilt and Power Telescopic Steering Column) | Refer to REMOVAL [10/2014 - ] | |
| "Steering Power Low Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Power steering system (for Manual Tilt and Manual Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Power steering system (for Power Tilt and Power Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Power steering ECU assembly (for Manual Tilt and Manual Telescopic Steering Column) | Refer to REMOVAL [10/2014 - ] | |
| Power steering ECU assembly (for Power Tilt and Power Telescopic Steering Column) | Refer to REMOVAL [10/2014 - ] | |
| "Power Steering Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Power steering system (for Manual Tilt and Manual Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Power steering system (for Power Tilt and Power Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Power steering ECU assembly (for Manual Tilt and Manual Telescopic Steering Column) | Refer to REMOVAL [10/2014 - ] | |
| Power steering ECU assembly (for Power Tilt and Power Telescopic Steering Column) | Refer to REMOVAL [10/2014 - ] | |
| "Engine Stopped Steering Power Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Power steering system (for Manual Tilt and Manual Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Power steering system (for Power Tilt and Power Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Power steering ECU assembly (for Manual Tilt and Manual Telescopic Steering Column) | Refer to REMOVAL [10/2014 - ] | |
| Power steering ECU assembly (for Power Tilt and Power Telescopic Steering Column) | Refer to REMOVAL [10/2014 - ] | |
| "SRS Airbag System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Airbag system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Airbag ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Headlight System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lighting system (w/ Headlight ECU) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Lighting system (w/o Headlight ECU) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Automatic high beam level control system (w/ Automatic High Beam Level Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Automatic high beam system (w/ Automatic High Beam System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Headlight light control ECU sub-assembly (for Triple Beam Headlight) | Refer to REMOVAL [09/2017 - ] | |
| "To Activate Auto High Beam, Switch Headlights to High Beam" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Automatic High Beam System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Automatic high beam system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Headlight light control ECU sub-assembly | Refer to REMOVAL [09/2017 - ] | |
| Pre-collision display is not displayed (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "BRAKE !" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "VSC Turned Off Pre-collision Brake System Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Pre-collision System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Pre-collision System Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Pre-collision System Turned Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Front Camera Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Front Camera Vision Blocked Clean and Demist Windshield" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "RADAR READY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Operate Cruise Lever or Accelerator Pedal to Resume" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "CRUISE NOT AVAILABLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "PRECEDING VEHICLE MOVEMENT" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "WAITING" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Mute PKSA Temporarily" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Intuitive parking assist system (w/ Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Intuitive parking assist system (w/o Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "PKSA Muted Temporarily" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Intuitive parking assist system (w/ Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Intuitive parking assist system (w/o Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "ADJUSTING LDA CAMERA" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Hold Steering Wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| "LDA Steering Assist Unavailable Hold Steering Wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| Lane departure alert display is not displayed (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Lane Departure Alert Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Lane Departure Alert Unavailable Camera Overheated" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| "LDA Steering Assist Deactivated Warnings Available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Lane Departure Alert Turned On Steering Assist Active" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Lane Departure Alert Turned On Steering Assist Inactive" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Lane Departure Alert Unavailable Below Approx 50km/h" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Lane Departure Alert Unavailable Below Approx 32MPH" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Lane Departure Alert Unavailable at Current Speed" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| Dynamic radar cruise display is not displayed (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Would You Like to Take a Rest?" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system (w/o Steering Control) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Lane departure alert system (w/ Steering Control) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Please Take a Rest" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane Departure Alert System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lane departure alert system (w/o Steering Control) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Lane departure alert system (w/ Steering Control) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| "ADJUSTING FRONT RADAR BEAM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "CHECKING CRUISE CONTROL C/D" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Driving support ECU assembly (w/ Dynamic Radar Cruise Control System) | Refer to REMOVAL [09/2017 - 05/2019] | |
| "CHECKING CRUISE CONTROL BRAKE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Driving support ECU assembly (w/ Dynamic Radar Cruise Control System) | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Radar Cruise Control Unavailable Clean Sensor" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Radar Cruise Control Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Radar Cruise Control Unavailable Depress Brake to Resume Driving" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Radar Cruise Active Please Pay Attention to Other Vehicles" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Cruise Control Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Driving support ECU assembly (w/ Dynamic Radar Cruise Control System) | Refer to REMOVAL [09/2017 - 05/2019] | |
| "Cruise Control Fault Press Brake to Deactivate Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Driving support ECU assembly (w/ Dynamic Radar Cruise Control System) | Refer to REMOVAL [09/2017 - 05/2019] | |
| Intuitive parking assist display is not displayed (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Intuitive parking assist system (w/ Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Intuitive parking assist system (w/o Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Parking Assist Malfunction Vist Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Intuitive parking assist system (w/ Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Intuitive parking assist system (w/o Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Parking Assist Unavailable Clean Parking Assist Sensor" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Intuitive parking assist system (w/ Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Intuitive parking assist system (w/o Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Blind Spot Monitor Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Blind Spot Monitor System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Blind spot monitor system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Blind spot monitor sensor LH | Refer to REMOVAL [09/2017 - ] | |
| "Blind Spot Monitor System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Blind Spot Monitor System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Blind spot monitor system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Blind spot monitor sensor LH | Refer to REMOVAL [09/2017 - ] | |
| "Moon Roof Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Sliding Roof System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Sliding roof system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Window Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Power window control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Window or Moon Roof Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Sliding Roof System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Power window control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Sliding roof system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "High Power Consumption Partial Limit On AC/Heater Operation" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Air conditioning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Air conditioning amplifier assembly | Refer to REMOVAL [09/2017 - ] | |
| "Theft Sensor Turned Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Theft deterrent system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Theft Sensor Turned On" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Theft deterrent system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| "Turn Lights Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lighting system (w/ Headlight ECU) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Lighting system (w/o Headlight ECU) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| Dead pixels on multi-information display | Perform Active Test [Meter Display 1] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Multi-information display customize setting does not operate | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
HINT:
*A: Items for consideration regarding ambient temperature display value
- The display value of the ambient temperature around the sensor changes due to the effects of heat radiated from the engine room and vehicle speed.
- Depending on the driving status, the ambient temperature of the air surrounding the vehicle and the displayed value are different and the speed at which the displayed value updates is delayed. However, this is not a malfunction. When the vehicle is stopped or being driven at a low speed, the value is not updated to a higher temperature in order to minimize the effects of the radiated heat from the engine on the auto air conditioning control. Since the same adjustment occurs while the vehicle is being driven at medium to high speeds, updating to a higher temperature is delayed. However, the value is updated to a lower temperature regardless of the vehicle speed.
BUZZER
| Symptom | Suspected Area | Link |
|---|---|---|
| All buzzers do not operate normally | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| Shift reject buzzer does not operate | SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Engine coolant temperature buzzer does not operate | SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Seat belt warning buzzer does not operate (Front seat belt warning light operates normally) | Check customize setting | Refer to CUSTOMIZE PARAMETERS [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Immobiliser certification buzzer does not operate | Immobiliser system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| Smart access system with push-button start warning buzzer does not operate | Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| Engine switch operation while driving warning buzzer does not operate | Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| Restart while driving notification buzzer does not operate | Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| Vehicle roll-away notification buzzer malfunction (Speedometer and tachometer operate normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Driving with door ajar warning buzzer does not operate (Open door warning light and speedometer operate normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| PKB-ON driving warning buzzer does not operate (Brake warning light and speedometer operate normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| EPS warning buzzer does not operate (Power steering system operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| Radar cruise control low speed cancel buzzer does not operate (w/ Dynamic Radar Cruise Control System) | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| Radar cruise low speed range preceding vehicle lost buzzer does not operate (w/ Dynamic Radar Cruise Control System) | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2017 - 05/2019] | |
| Multi-information display warning buzzer does not operate | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| Flasher buzzer does not operate (Turn indicator light normally) | Check customize setting | Refer to CUSTOMIZE PARAMETERS [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Oil pressure warning buzzer does not operate | SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - 05/2019] | |
| Brake fluid low warning buzzer does not operate | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| Lane departure alert cancel buzzer does not operate (w/ Lane Departure Alert System) | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| Lane departure warning buzzer does not operate (w/ Lane Departure Alert System) | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| Lane departure alert hands off steering wheel warning buzzer does not operate (w/ Lane Departure Alert System) | Lane departure alert system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane departure warning camera | Refer to REMOVAL [09/2017 - 05/2019] | |
| Brake hold control unreleased warning buzzer does not operate | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| EPB* cancel buzzer does not operate | Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [10/2014 - 05/2019] | |
| Power window / sliding roof warning buzzer malfunction | Power window control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Sliding roof system (w/ Sliding Roof System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| Light reminder warning buzzer does not operate | Lighting system (w/ Headlight ECU) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lighting system (w/o Headlight ECU) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] |
OTHERS
| Symptom | Suspected Area | Link |
|---|---|---|
| DTCs display malfunction (Other systems operate normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| Operating light control rheostat does not change light brightness | Refer to "Operating Light Control Rheostat does not Change Light Brightness" | Refer to Operating Light Control Rheostat does not Change Light Brightness [10/2014 - ] |
| Meter illumination is always dark | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] |
| Lighting system (w/ Headlight ECU) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Lighting system (w/o Headlight ECU) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 05/2019] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [10/2014 - 05/2019] | |
| Operating ODO/TRIP switch does not change ODO/TRIP meter display | Refer to "Odo/Trip Switch Malfunction" | Refer to Odo/Trip Switch Malfunction [10/2014 - ] |
| Multi-information display does not change using steering pad switch assembly | Read the Data List [Multi Switch (Up), Multi Switch (Down), Multi Switch (Menu), Multi Switch (Enter), Multi Switch (Right), Multi Switch (Left)] | Refer to DATA LIST / ACTIVE TEST [09/2017 - 05/2019] |
| Steering pad switch assembly | Refer to INSPECTION [09/2017 - ] | |
| Spiral cable sub-assembly | Refer to INSPECTION [09/2017 - ] | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] |