LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2021 >> LS 500h RWD >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Airbag System (W/O Advanced Park) - Diagnostic Codes (3 Of 3) >> AIRBAG SYSTEM (w/o Advanced Park) >> DTC B1880: Short in Rear Seat Cushion Squib RH Circuit; DTC B1881: Open in Rear Seat Cushion Squib RH Circuit; DTC B1882: Short to GND in Rear Seat Cushion Squib RH Circuit; DTC B1883: Short to B+ in Rear Seat Cushion Squib RH Circuit [10/2020 - 10/2023] >> Procedure

DTC B1880: Short in Rear Seat Cushion Squib RH Circuit; DTC B1881: Open in Rear Seat Cushion Squib RH Circuit; DTC B1882: Short to GND in Rear Seat Cushion Squib RH Circuit; DTC B1883: Short to B+ in Rear Seat Cushion Squib RH Circuit [10/2020 - 10/2023]: Procedure

  1. CHECK CONNECTORS 
    1. Turn the power switch off.
      GTY794183Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Seat Cushion Airbag Assembly RH
      *2 Airbag ECU Assembly
      *3 Rear Seat Wire RH
      *4 Floor Wire
    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    3. Check that the connectors are properly connected to the rear seat cushion airbag assembly RH and airbag ECU assembly.

      OK

      The connectors are properly connected.

      HINT: 

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the rear seat cushion airbag assembly RH and airbag ECU assembly.
    5. Check that the terminals of the connectors are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

    6. Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

      OK

      The short springs are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FLOOR WIRE OR REAR SEAT WIRE RH 

    Result: 

    OK 

    See step  2

  2. CHECK REAR SEAT CUSHION AIRBAG ASSEMBLY RH 
    1. Connect the connector to the airbag ECU assembly.
      GTY782989Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Seat Cushion Airbag Assembly RH
      *2 Airbag ECU Assembly
      *3 SST
      *a Front view of wire harness connector
      (to Rear Seat Cushion Airbag Assembly RH)
    2. Connect the black wire side of SST (resistance: 2.1 Ω) to connector C.
      WARNING:

      Never connect the tester to the rear seat cushion airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.

      NOTE:
      • Do not forcibly insert SST into the terminals of the connector when connecting SST.
      • Insert SST straight into the terminals of the connector.
      • SST: 09843-18061 
    3. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
    4. Turn the power switch on (IG), and wait for at least 60 seconds.
    5. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [10/2020 - 10/2023]

      Body Electrical > SRS Airbag > Clear DTCs 

    6. Turn the power switch off.
    7. Turn the power switch on (IG), and wait for at least 60 seconds.
    8. Check for DTCs.

      Refer to DTC CHECK / CLEAR [10/2020 - 10/2023]

      Body Electrical > SRS Airbag > Trouble Codes 

      Result

      Proceed to
      DTC B1880, B1881, B1882 and B1883 are not output
      DTC B1880, B1881, B1882 or B1883 is output

      HINT: 

      Codes other than DTC B1880, B1881, B1882 and B1883 may be output at this time, but they are not related to this check.

    9. Turn the power switch off.
    10. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    11. Disconnect SST from connector C.

    Result: 

    DTC B1880, B1881, B1882 and B1883 are not output 

    REPLACE REAR SEAT CUSHION AIRBAG ASSEMBLY RH. Refer to  REMOVAL [10/2020 - 11/2021]  , or refer to  REMOVAL [11/2021 - 10/2022]  , or refer to  REMOVAL [10/2022 - 10/2023] 

    Result: 

    DTC B1880, B1881, B1882 or B1883 is output 

    See step  3

  3. CHECK REAR SEAT CUSHION AIRBAG ASSEMBLY RH CIRCUIT 
    1. Disconnect the floor wire from the airbag ECU assembly.
      GTY798805Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Seat Cushion Airbag Assembly RH
      *2 Airbag ECU Assembly
      *3 Rear Seat Wire RH
      *4 Floor Wire
      *a Front view of wire harness connector
      (to Rear Seat Cushion Airbag Assembly RH)
      Release the activation prevention mechanism
    2. Check for a short to B+ in the circuit.
      1. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
      2. Turn the power switch on (IG).
      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        Tester Connection Switch Condition Specified Condition
        R28-1 - Body ground Power switch on (IG) Below 1 V
        R28-2 - Body ground Power switch on (IG) Below 1 V
      4. Turn the power switch off.
      5. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    3. Check for an open in the circuit.
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        R28-1 - R28-2 Always Below 1 Ω
    4. Check for a short to ground in the circuit.
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        R28-1 - Body ground Always 1 MΩ or higher
        R28-2 - Body ground Always 1 MΩ or higher
    5. Check for a short in the circuit.
      1. Release the activation prevention mechanism built into connector B.

        Refer to SYSTEM DESCRIPTION [10/2020 - 10/2023]

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        R28-1 - R28-2 Always 1 MΩ or higher
      3. Restore the released activation prevention mechanism of connector B to the original condition.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  5

    Result: 

    OK 

    See step  4

  4. CHECK DTC 
    1. Connect the connectors to the rear seat cushion airbag assembly RH and airbag ECU assembly.
      GTY784445Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Seat Cushion Airbag Assembly RH
      *2 Airbag ECU Assembly
    2. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
    3. Turn the power switch on (IG), and wait for at least 60 seconds.
    4. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [10/2020 - 10/2023]

      Body Electrical > SRS Airbag > Clear DTCs 

    5. Turn the power switch off.
    6. Turn the power switch on (IG), and wait for at least 60 seconds.
    7. Check for DTCs.

      Refer to DTC CHECK / CLEAR [10/2020 - 10/2023]

      Body Electrical > SRS Airbag > Trouble Codes 

      Result

      Proceed to
      DTC B1880, B1881, B1882 and B1883 are not output
      DTC B1880, B1881, B1882 or B1883 is output

      HINT: 

      Codes other than DTC B1880, B1881, B1882 and B1883 may be output at this time, but they are not related to this check.

    Result: 

    DTC B1880, B1881, B1882 and B1883 are not output 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2020 - 11/2021]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2021 - 10/2022]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2022 - 10/2023] 

    Result: 

    DTC B1880, B1881, B1882 or B1883 is output 

    REPLACE AIRBAG ECU ASSEMBLY. Refer to  REMOVAL [10/2020 - 11/2021]  , or refer to  REMOVAL [11/2021 - 10/2022]  , or refer to  REMOVAL [10/2022 - 10/2023] 

  5. CHECK FLOOR WIRE 
    1. Disconnect the floor wire from the rear seat wire RH.
      GTY968112Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Seat Airbag Assembly RH
      *2 Airbag ECU Assembly
      *3 Rear Seat Wire RH
      *4 Floor Wire
      *a Front view of wire harness connector
      (to Rear Seat Airbag Assembly RH)
      Release the activation prevention mechanism
    2. Check for a short to B+ in the circuit.
      1. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
      2. Turn the power switch on (IG).
      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        Tester Connection Condition Specified Condition
        LR 7-1 (RCR+) - Body ground Power switch on (IG) Below 1 V
        LR 7-2 (RCR-) - Body ground Power switch on (IG) Below 1 V
      4. Turn the power switch off.
      5. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    3. Check for an open in the circuit.
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        LR 7-1 (RCR+) - LR 7-2 (RCR-) Always Below 1 Ω
    4. Check for a short to ground in the circuit.
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        LR 7-1 (RCR+) - Body ground Always 1 MΩ or higher
        LR 7-2 (RCR-) - Body ground Always 1 MΩ or higher
    5. Check for a short in the circuit.
      1. Release the activation prevention mechanism built into connector B.

        Refer to SYSTEM DESCRIPTION [10/2020 - 10/2023]

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        LR 7-1 (RCR+) - LR 7-2 (RCR-) Always 1 MΩ or higher
      3. Restore the released activation prevention mechanism of connector B to the original condition.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REAR SEAT WIRE RH 

    Result: 

    NG 

    REPLACE FLOOR WIRE 

scientia non olet · About LEMON Manuals