LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2021 >> LS 500h RWD >> Repair and Diagnosis >> Brakes >> Mechanical - Hydraulic >> Electronically Controlled Brake System (W/O Advanced Park) - Diagnostic Codes (2 Of 3) >> ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Advanced Park) >> DTC C1315: SMC1 Changeover Solenoid; DTC C1316: SMC2 Changeover Solenoid; DTC C1352: Increasing Pressure Solenoid (FR); DTC C1353: Increasing Pressure Solenoid (FL); DTC C1354: Increasing Pressure Solenoid (RR); DTC C1355: Increasing Pressure Solenoid (RL); DTC C1356: Decreasing Pressure Solenoid (FR); DTC C1357: Decreasing Pressure Solenoid (FL); DTC C1358: Decreasing Pressure Solenoid (RR); DTC C1359: Decreasing Pressure Solenoid (RL) [10/2020 - 10/2023] >> Description

DTC C1315: SMC1 Changeover Solenoid; DTC C1316: SMC2 Changeover Solenoid; DTC C1352: Increasing Pressure Solenoid (FR); DTC C1353: Increasing Pressure Solenoid (FL); DTC C1354: Increasing Pressure Solenoid (RR); DTC C1355: Increasing Pressure Solenoid (RL); DTC C1356: Decreasing Pressure Solenoid (FR); DTC C1357: Decreasing Pressure Solenoid (FL); DTC C1358: Decreasing Pressure Solenoid (RR); DTC C1359: Decreasing Pressure Solenoid (RL) [10/2020 - 10/2023]: Description

Each solenoid adjusts the pressure which affects each wheel cylinder according to signals from the skid control ECU assembly and controls the vehicle.

The master cut solenoid (SMC1/2) is closed and blocks the master cylinder pressure from the electronically controlled brake system control pressure when the system is normal. The master cut solenoid is open and sends the master cylinder hydraulic pressure to the non-assisted brake wheel cylinders during fail-safe operation due to a system malfunction.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area MIL Note
C1315 SMC1 Changeover Solenoid 61
62
63
64
  • INF Code: 61
    • Either of the following is detected:
      1. SMC1 drive circuit is malfunctioning for 0.05 seconds or more.
      2. Short to +B in SMC1.
  • INF Code: 62
    • Current leaks for 0.05 seconds or more when SMC1 is off.
  • INF Code: 63
    • Open circuit in SMC1 continues for 0.05 seconds or more.
  • INF Code: 64
    • Overcurrent in SMC1 continues for 0.05 seconds or more.
  • INF Code: 61, 62, 63
    • Open or short in wire harness
    • Master cut solenoid (SMC1) circuit
    • Skid control ECU assembly
  • INF Code: 64
    • Short in wire harness
    • Master cut solenoid (SMC1) circuit
    • Skid control ECU assembly
Comes on
  • INF Code 61: SAE Code C13CA
  • INF Code 62: SAE Code C13CC (Case 1)
  • INF Code 63: SAE Code C13CB
  • INF Code 64: SAE Code C13CC (Case 2)
C1316 SMC2 Changeover Solenoid 66
67
68
69
  • INF Code: 66
    • Either of the following is detected:
      1. SMC2 drive circuit is malfunctioning for 0.05 seconds or more.
      2. Short to +B in SMC2.
  • INF Code: 67
    • Current leaks for 0.05 seconds or more when SMC2 is off.
  • INF Code: 68
    • Open circuit in SMC2 continues for 0.05 seconds or more.
  • INF Code: 69
    • Overcurrent in SMC2 continues for 0.05 seconds or more.
  • INF Code: 66, 67, 68
    • Open or short in wire harness
    • Master cut solenoid (SMC2) circuit
    • Skid control ECU assembly
  • INF Code: 69
    • Short in wire harness
    • Master cut solenoid (SMC2) circuit
    • Skid control ECU assembly
Comes on
  • INF Code 66: SAE Code C14F2
  • INF Code 67: SAE Code C14F4 (Case 1)
  • INF Code 68: SAE Code C14F3
  • INF Code 69: SAE Code C14F4 (Case 2)
C1352 Increasing Pressure Solenoid (FR) 11
12
13
14
  • INF Code: 11
    • Open circuit in FRA continues for 0.05 seconds or more when FRA is off.
  • INF Code: 12
    • Open circuit in FRA continues for 0.05 seconds or more when FRA is on.
  • INF Code: 13
    • Short to +B or voltage leak in FRA continues for 0.05 seconds or more.
  • INF Code: 14
    • Overcurrent in FRA continues for 0.05 seconds or more.
  • INF Code: 11, 12
    • Open or short in wire harness
    • Improperly connected connector, deformation or corrosion of terminals
    • Brake actuator assembly
    • Skid control ECU assembly
  • INF Code: 13, 14
    • Short in wire harness
    • Brake actuator assembly
    • Skid control ECU assembly
Comes on
  • INF Code 11: SAE Code C12BD (Case 1)
  • INF Code 12: SAE Code C12BD (Case 2 and 3)
  • INF Code 13: SAE Code C12BE (Case 1)
  • INF Code 14: SAE Code C12BE (Case 2)
C1353 Increasing Pressure Solenoid (FL) 21
22
23
24
  • INF Code: 21
    • Open circuit in FLA continues for 0.05 seconds or more when FLA is off.
  • INF Code: 22
    • Open circuit in FLA continues for 0.05 seconds or more when FLA is on.
  • INF Code: 23
    • Short to +B or voltage leak in FLA continues for 0.05 seconds or more.
  • INF Code: 24
    • Overcurrent in FLA continues for 0.05 seconds or more.
  • INF Code: 21, 22
    • Open or short in wire harness
    • Improperly connected connector, deformation or corrosion of terminals
    • Brake actuator assembly
    • Skid control ECU assembly
  • INF Code: 23, 24
    • Short in wire harness
    • Brake actuator assembly
    • Skid control ECU assembly
Comes on
  • INF Code 21: SAE Code C12A7 (Case 1)
  • INF Code 22: SAE Code C12A7 (Case 2 and 3)
  • INF Code 23: SAE Code C12A8 (Case 1)
  • INF Code 24: SAE Code C12A8 (Case 2)
C1354 Increasing Pressure Solenoid (RR) 31
32
33
34
  • INF Code: 31
    • Open circuit in RRA continues for 0.05 seconds or more when RRA is off.
  • INF Code: 32
    • Open circuit in RRA continues for 0.05 seconds or more when RRA is on.
  • INF Code: 33
    • Short to +B or voltage leak in RRA continues for 0.05 seconds or more.
  • INF Code: 34
    • Overcurrent in RRA continues for 0.05 seconds or more.
  • INF Code: 31, 32
    • Open or short in wire harness
    • Improperly connected connector, deformation or corrosion of terminals
    • Brake actuator assembly
    • Skid control ECU assembly
  • INF Code: 33, 34
    • Short in wire harness
    • Brake actuator assembly
    • Skid control ECU assembly
Comes on
  • INF Code 31: SAE Code C12E9 (Case 1)
  • INF Code 32: SAE Code C12E9 (Case 2 and 3)
  • INF Code 33: SAE Code C12EA (Case 1)
  • INF Code 34: SAE Code C12EA (Case 2)
C1355 Increasing Pressure Solenoid (RL) 41
42
43
44
  • INF Code: 41
    • Open circuit in RLA continues for 0.05 seconds or more when RLA is off.
  • INF Code: 42
    • Open circuit in RLA continues for 0.05 seconds or more when RLA is on.
  • INF Code: 43
    • Short to +B or voltage leak in RLA continues for 0.05 seconds or more.
  • INF Code: 44
    • Overcurrent in RLA continues for 0.05 seconds or more.
  • INF Code: 41, 42
    • Open or short in wire harness
    • Improperly connected connector, deformation or corrosion of terminals
    • Brake actuator assembly
    • Skid control ECU assembly
  • INF Code: 43, 44
    • Short in wire harness
    • Brake actuator assembly
    • Skid control ECU assembly
Comes on
  • INF Code 41: SAE Code C12D3 (Case 1)
  • INF Code 42: SAE Code C12D3 (Case 2 and 3)
  • INF Code 43: SAE Code C12D4 (Case 1)
  • INF Code 44: SAE Code C12D4 (Case 2)
C1356 Decreasing Pressure Solenoid (FR) 16
17
18
19
  • INF Code: 16
    • Open circuit in FRR continues for 0.05 seconds or more when FRR is off.
  • INF Code: 17
    • Open circuit in FRR continues for 0.05 seconds or more when FRR is on.
  • INF Code: 18
    • Short to +B or voltage leak in FRR continues for 0.05 seconds or more.
  • INF Code: 19
    • Overcurrent in FRR continues for 0.05 seconds or more.
  • INF Code: 16, 17
    • Open or short in wire harness
    • Improperly connected connector, deformation or corrosion of terminals
    • Brake actuator assembly
    • Skid control ECU assembly
  • INF Code: 18, 19
    • Short in wire harness
    • Brake actuator assembly
    • Skid control ECU assembly
Comes on
  • INF Code 16: SAE Code C12C8 (Case 1)
  • INF Code 17: SAE Code C12C8 (Case 2 and 3)
  • INF Code 18: SAE Code C12C9 (Case 1)
  • INF Code 19: SAE Code C12C9 (Case 2)
C1357 Decreasing Pressure Solenoid (FL) 26
27
28
29
  • INF Code: 26
    • Open circuit in FLR continues for 0.05 seconds or more when FLR is off.
  • INF Code: 27
    • Open circuit in FLR continues for 0.05 seconds or more when FLR is on.
  • INF Code: 28
    • Short to +B or voltage leak in FLR continues for 0.05 seconds or more.
  • INF Code: 29
    • Overcurrent in FLR continues for 0.05 seconds or more.
  • INF Code: 26, 27
    • Open or short in wire harness
    • Improperly connected connector, deformation or corrosion of terminals
    • Brake actuator assembly
    • Skid control ECU assembly
  • INF Code: 28, 29
    • Short in wire harness
    • Brake actuator assembly
    • Skid control ECU assembly
Comes on
  • INF Code 26: SAE Code C12B2 (Case 1)
  • INF Code 27: SAE Code C12B2 (Case 2 and 3)
  • INF Code 28: SAE Code C12B3 (Case 1)
  • INF Code 29: SAE Code C12B3 (Case 2)
C1358 Decreasing Pressure Solenoid (RR) 36
37
38
39
  • INF Code: 36
    • Open circuit in RRR continues for 0.05 seconds or more when RRR is off.
  • INF Code: 37
    • Open circuit in RRR continues for 0.05 seconds or more when RRR is on.
  • INF Code: 38
    • Short to +B or voltage leak in RRR continues for 0.05 seconds or more.
  • INF Code: 39
    • Overcurrent in RRR continues for 0.05 seconds or more.
  • INF Code: 36, 37
    • Open or short in wire harness
    • Improperly connected connector, deformation or corrosion of terminals
    • Brake actuator assembly
    • Skid control ECU assembly
  • INF Code: 38, 39
    • Short in wire harness
    • Brake actuator assembly
    • Skid control ECU assembly
Comes on
  • INF Code 36: SAE Code C12F4 (Case 1)
  • INF Code 37: SAE Code C12F4 (Case 2 and 3)
  • INF Code 38: SAE Code C12F5 (Case 1)
  • INF Code 39: SAE Code C12F5 (Case 2)
C1359 Decreasing Pressure Solenoid (RL) 46
47
48
49
  • INF Code: 46
    • Open circuit in RLR continues for 0.05 seconds or more when RLR is off.
  • INF Code: 47
    • Open circuit in RLR continues for 0.05 seconds or more when RLR is on.
  • INF Code: 48
    • Short to +B or voltage leak in RLR continues for 0.05 seconds or more.
  • INF Code: 49
    • Overcurrent in RLR continues for 0.05 seconds or more.
  • INF Code: 46, 47
    • Open or short in wire harness
    • Improperly connected connector, deformation or corrosion of terminals
    • Brake actuator assembly
    • Skid control ECU assembly
  • INF Code: 48, 49
    • Short in wire harness
    • Brake actuator assembly
    • Skid control ECU assembly
Comes on
  • INF Code 46: SAE Code C12DE (Case 1)
  • INF Code 47: SAE Code C12DE (Case 2 and 3)
  • INF Code 48: SAE Code C12DF (Case 1)
  • INF Code 49: SAE Code C12DF (Case 2)