Fuel Receiver Gauge Display Malfunction [10/2020 - 11/2021]: Procedure

1. Check DTCs are output.

   Refer to DTC CHECK / CLEAR [10/2017 - ]

   Body Electrical > Combination Meter > Trouble Codes 

   OK

   DTCs are not output.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2020 - 11/2021] 

Result: 

OK 

See step  2

1. Check if SFI system DTCs are output.

   Refer to DTC CHECK / CLEAR [10/2020 - 10/2023]

   Powertrain > Engine > Trouble Codes 

   OK

   SFI system DTCs are not output.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO SFI SYSTEM. Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2020 - 11/2021] 

Result: 

OK 

See step  3

1. Check vehicle condition.

   Result

   Result	Proceed to
   for F SPORT Model	A
   w/ Advanced Drive
   except F SPORT Model	B
   w/o Advanced Drive

Result: 

B 

See step  5

Result: 

A 

See step  4

1. Connect the GTS to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Combination Meter / Data List.
5. Read the Data List according to the display on the GTS.

   Body Electrical > Combination Meter > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Fuel Input	Fuel input	Min.: 0 L, Max.: 655.34 L or Unset	Current fuel level displayed	-
   Sub Fuel Input	Sub fuel input	Min.: 0 L, Max.: 655.34 L or Unset	Current fuel level displayed	-

   Body Electrical > Combination Meter > Data List 

   Tester Display
   Fuel Input
   Sub Fuel Input

   OK

   Fuel level displayed on the Techstream is almost the same as the fuel receiver gauge indication.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

See step  6

Result: 

NG 

REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [10/2020 - 11/2021] 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Combination Meter / Active Test.
5. Perform the Active Test according to the display on the Techstream.

   Refer to DATA LIST / ACTIVE TEST [10/2020 - 11/2021]

   Body Electrical > Combination Meter > Active Test 

   Tester Display	Measurement Item	Control Range
   Fuel Gauge Operation (Sender E)	Fuel receiver gauge (Sender E)	ON
   Fuel Gauge Operation (Empty)	Fuel receiver gauge (Empty)	ON
   Fuel Gauge Operation (Warning)	Fuel receiver gauge (Warning)	ON
   Fuel Gauge Operation (1/4)	Fuel receiver gauge (1/4)	ON
   Fuel Gauge Operation (1/2)	Fuel receiver gauge (1/2)	ON
   Fuel Gauge Operation (3/4)	Fuel receiver gauge (3/4)	ON
   Fuel Gauge Operation (Full)	Fuel receiver gauge (Full)	ON
   Fuel Gauge Operation (Sender F)	Fuel receiver gauge (Sender F)	ON

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Fuel Gauge Operation (Sender E)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Fuel Gauge Operation (Empty)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Fuel Gauge Operation (Warning)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Fuel Gauge Operation (1/4)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Fuel Gauge Operation (1/2)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Fuel Gauge Operation (3/4)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Fuel Gauge Operation (Full)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Fuel Gauge Operation (Sender F)

   OK

   Fuel receiver gauge indication is normal.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [10/2020 - 11/2021] 

Result: 

OK 

See step  6

1. Remove the fuel sender gauge assembly.

   Refer to REMOVAL [10/2020 - 10/2022]

2. Inspect the fuel sender gauge assembly.

   Refer to INSPECTION [10/2017 - ]

   Result

   Result	Proceed to
   OK	A
   NG (for Fuel suction gauge assembly)	B
   NG (for No. 2 fuel sender gauge assembly)	C

Result: 

A 

CLEAN INSIDE OF FUEL TANK ASSEMBLY 

Result: 

B 

REPLACE FUEL SENDER GAUGE ASSEMBLY. Refer to  REMOVAL [10/2020 - 10/2022] 

Result: 

C 

REPLACE NO. 2 FUEL SENDER GAUGE ASSEMBLY. Refer to  REMOVAL [10/2020 - 10/2022]