Television Display does not Turn ON [12/2017 - 10/2022]: Procedure

1. Check which television display assembly does not operate.

   Result

   Result	Proceed to
   Television display assembly LH does not operate.	A
   Television display assembly RH does not operate.	B
   Television display assembly LH and television display assembly RH does not operate.	C

Result: 

B 

See step  4

Result: 

C 

See step  6

Result: 

A 

See step  2

1. Disconnect the L142 television display assembly RH connector.
2. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   L142-12 - Body ground	Engine switch on (ACC)	4.2 to 5.5 V

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY. Refer to  REMOVAL [12/2017 - 10/2022] 

Result: 

OK 

See step  3

1. Disconnect the L138 multi-display controller sub-assembly connector.
2. Disconnect the L142 television display assembly RH connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   L138-4 (ONR) - L142-12	Always	Below 1 Ω
   L138-4 (ONR) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [12/2017 - 09/2019]  , or refer to  PROBLEM SYMPTOMS TABLE [09/2019 - 10/2022] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

1. Disconnect the L141 television display assembly LH connector.
2. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   L141-12 - Body ground	Engine switch on (ACC)	4.2 to 5.5 V

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY. Refer to  REMOVAL [12/2017 - 10/2022] 

Result: 

OK 

See step  5

1. Disconnect the L138 multi-display controller sub-assembly connector.
2. Disconnect the L141 television display assembly LH connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   L138-5 (ONL) - L141-12	Always	Below 1 Ω
   L138-5 (ONL) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [12/2017 - 09/2019]  , or refer to  PROBLEM SYMPTOMS TABLE [09/2019 - 10/2022] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

1. Disconnect the L138 multi-display controller sub-assembly connector.
2. Disconnect the L142 television display assembly RH connector.
3. Disconnect the L141 television display assembly LH connector.
4. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   L138-4 (ONR) - L142-12	Always	Below 1 Ω
   L138-5 (ONL) - L141-12	Always	Below 1 Ω
   L138-4 (ONR) - Body ground	Always	10 kΩ or higher
   L138-5 (ONL) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [12/2017 - 09/2019]  , or refer to  PROBLEM SYMPTOMS TABLE [09/2019 - 10/2022] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR