VSC OFF Switch Circuit [12/2017 - 09/2018]: Procedure

1. Check if CAN communication system DTCs are output.

   Refer to DIAGNOSIS SYSTEM [12/2017 - 09/2018]

   Result

   Result	Proceed to
   DTCs are not output.	A
   DTCs are output.	B

Result: 

B 

CHECK CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2017 - 09/2018] 

Result: 

A 

See step  2

1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

   OK

   The connector is securely connected.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY 

Result: 

OK 

See step  3

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Select the Data List on the Techstream.

   Refer to DATA LIST / ACTIVE TEST [12/2017 - 09/2018]

   Chassis > ABS/VSC/TRAC > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   TRAC/VSC Off Mode	TRAC/VSC off mode	Normal, TRAC OFF or VSC OFF	Normal: Normal mode TRAC OFF: TRAC off mode VSC OFF: VSC off mode	-

   Chassis > ABS/VSC/TRAC > Data List 

   Tester Display
   TRAC/VSC Off Mode

4. Check that the indicator light and mode condition on the Techstream change according to VSC OFF switch (No. 2 satellite switch set) operation.

   Standard

   Switch Operation	Mode Condition Display	Multi-information Display (TRAC OFF Message)	VSC OFF Indicator Light
   Not pressed	Normal	Not displayed	Does not come on
   Pressing the VSC OFF switch (No. 2 satellite switch set)	TRAC OFF	Displayed	Does not come on
   Pressing and holding the VSC OFF switch (No. 2 satellite switch set)	VSC OFF	Displayed	Comes on

   Result

   Result	Proceed to
   Indicator light and mode condition display do not change.	A
   Mode condition display is normal, but indicator light does not change.	B
   Indicator light and mode condition display are normal.	C

Result: 

B 

INSPECT METER / GAUGE SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2017 - 10/2023] 

Result: 

C 

USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2017 - 09/2018] 

Result: 

A 

See step  4

1. Select the Active Test on the Techstream.

   Refer to DATA LIST / ACTIVE TEST [12/2017 - 09/2018]

   Chassis > ABS/VSC/TRAC > Active Test 

   Tester Display	Measurement Item	Control Range	Diagnostic Note
   TRC(TRAC) OFF Indicator Light	Multi-information display (TRAC OFF message)	Display ON/OFF	Observe combination meter assembly
   VSC OFF Indicator Light	VSC OFF indicator light	Indicator light ON/OFF	Observe combination meter assembly

   Chassis > ABS/VSC/TRAC > Active Test 

   Tester Display
   TRC(TRAC) OFF Indicator Light

   Chassis > ABS/VSC/TRAC > Active Test 

   Tester Display
   VSC OFF Indicator Light

2. Check the multi-information display (TRAC OFF message) and VSC OFF indicator light on the combination meter assembly turn ON or OFF in accordance with the Techstream operation.

   OK

   The multi-information display (TRAC OFF message) and VSC OFF indicator light turn ON or OFF in accordance with the Techstream operation.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  7

Result: 

OK 

See step  5

1. Turn the engine switch off.
2. Remove the VSC OFF switch (No. 2 satellite switch set).

   Refer to REMOVAL [12/2017 - ]

3. Inspect the VSC OFF switch (No. 2 satellite switch set).

   Refer to INSPECTION [12/2017 - ]

   OK

   The VSC OFF switch (No. 2 satellite switch set) operates normally.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE NO. 2 SATELLITE SWITCH SET. Refer to  REMOVAL [12/2017 - ] 

Result: 

OK 

See step  6

1. Disconnect the A9 skid control ECU (brake actuator assembly) connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   A9-33 (CSW) - G59-2 (+)	Always	Below 1 Ω
   A9-33 (CSW) or G59-2 (+) - Body ground	Always	10 kΩ or higher
   G59-7 (E) - Body ground	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE BRAKE ACTUATOR ASSEMBLY. Refer to  REMOVAL [12/2017 - 09/2018] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

1. Turn the engine switch off.
2. Perform the Active Test of the combination meter assembly (meter CPU) using the Techstream.

   Refer to DATA LIST / ACTIVE TEST [12/2017 - 10/2020]

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Meter Display (All)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   VSC OFF Indicator

3. Check the combination meter assembly.

   OK

   The multi-information display and VSC OFF indicator light turns on or off in accordance with the Techstream operation.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE BRAKE ACTUATOR ASSEMBLY. Refer to  REMOVAL [12/2017 - 09/2018] 

Result: 

NG 

INSPECT METER / GAUGE SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2017 - 10/2023]