LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2021 >> LC 500h >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Audio / Video System - Service Information >> Instrument Panel Speaker >> Removal [01/2017 - ] >> Procedure

Removal [01/2017 - ]: Procedure

  1. REMOVE FRONT DOOR SCUFF PLATE LH 

    Refer to PROCEDURE - Step 10 [01/2017 - 06/2019] , or refer to PROCEDURE - Step 10 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 10 [04/2020 - 05/2023] , or refer to PROCEDURE - Step 10 [05/2023 - ]

  2. REMOVE FRONT DOOR OPENING TRIM COVER LH 

    Refer to PROCEDURE - Step 12 [01/2017 - 06/2019] , or refer to PROCEDURE - Step 12 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 12 [04/2020 - 05/2023] , or refer to PROCEDURE - Step 12 [05/2023 - ]

  3. REMOVE FRONT DOOR NO. 2 OPENING TRIM COVER LH 

    Refer to PROCEDURE - Step 14 [01/2017 - 06/2019] , or refer to PROCEDURE - Step 14 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 14 [04/2020 - 05/2023] , or refer to PROCEDURE - Step 14 [05/2023 - ]

  4. REMOVE FRONT PILLAR GARNISH LH 

    Refer to PROCEDURE - Step 12 [01/2017 - 05/2023] , or refer to PROCEDURE - Step 13 [05/2023 - ]

  5. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 35 [01/2017 - 06/2019] , or refer to PROCEDURE - Step 35 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 35 [04/2020 - 05/2023] , or refer to PROCEDURE - Step 40 [05/2023 - ]

  6. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY 
    NOTE:

    Do not touch the cone part of the speaker.

    1. Remove the 2 screws.
      GTY836650Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the connector and remove the front No. 1 speaker assembly.
  7. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY 
    1. Apply protective tape to the areas shown in the illustration to prevent damage in the following procedures.
      GTY825707Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protective tape
    2. Insert the moulding remover B between the instrument safety pad sub-assembly in the position shown in the illustration and create a gap.
      GTY817817Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using moulding remover A in the gap created in the previous procedure, detach the claws.
      GTY817815Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Move the No. 1 speaker opening cover assembly in the direction indicated by the arrow shown in the illustration.
      GTY790065Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    5. Detach the claw in the direction indicated by the arrow shown in the illustration.
      GTY817085Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    6. Detach the claw in the direction indicated by the arrow shown in the illustration and remove the No. 1 speaker opening cover assembly.
      GTY823018Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  8. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY 
    NOTE:

    Do not touch the cone part of the speaker.

    1. Remove the 2 screws.
      GTY836661Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the connector and remove the front No. 2 speaker assembly.
scientia non olet · About LEMON Manuals