Reassembly [03/2017 - 06/2019]: Procedure

HINT: 

When installing the rear bumper pad, heat the body rocker panel moulding assembly LH.

Standard

WARNING:

• Do not touch the heat light and heated parts.
• Touching the heat light may result in burns.
• Touching heated parts for a long time may result in burns.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Heated Part
*b	Heat Light

1. Clean the rear bumper pad installation surface with a non-residue solvent.
2. Remove the peeling paper on a new rear bumper pad while making sure not to touch the adhesional surface.
3. Install the rear bumper pad in the position shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Mark-off Line

   NOTE:

   Press the rear bumper pad firmly to install it.

HINT: 

When installing the No. 2 side mudguard protector, heat the body rocker panel moulding assembly LH.

Standard

WARNING:

• Do not touch the heat light and heated parts.
• Touching the heat light may result in burns.
• Touching heated parts for a long time may result in burns.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Heated Part
*b	Heat Light

1. Clean the No. 2 side mudguard protector installation surface with a non-residue solvent.
2. Remove the peeling paper on a new No. 2 side mudguard protector while making sure not to touch the adhesional surface.
3. Align the 2 No. 2 side mudguard protectors to the end of vehicle front side rib and install it.
   1. for Front Side:

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      *a

      Rib

      -

      -

   2. for Rear Side:

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      *a

      Rib

HINT: 

When installing the No. 6 rocker panel moulding protector, heat the body rocker panel moulding assembly LH.

Standard

WARNING:

• Do not touch the heat light and heated parts.
• Touching the heat light may result in burns.
• Touching heated parts for a long time may result in burns.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Heated Part
*b	Heat Light

1. Clean the No. 6 rocker panel moulding protector installation surface with a non-residue solvent.
2. Remove the peeling paper on a new No. 6 rocker panel moulding protector while making sure not to touch the adhesional surface.
3. Install the No. 6 rocker panel moulding protector in the position shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   R End

   -

   -

   NOTE:

   Press the rear bumper pad firmly to install it.

HINT: 

When installing the No. 2 rocker panel moulding protector, heat the body rocker panel moulding assembly LH.

Standard

WARNING:

• Do not touch the heat light and heated parts.
• Touching the heat light may result in burns.
• Touching heated parts for a long time may result in burns.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Heated Part
*b	Heat Light

1. Clean the No. 2 rocker panel moulding protector installation surface with a non-residue solvent.
2. Remove the peeling paper on a new No. 2 rocker panel moulding protector while making sure not to touch the adhesional surface.
3. Install the 2 No. 2 rocker panel moulding protectors in the position shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Mark-off Line

   -

   -

HINT: 

When installing the No. 1 rocker panel moulding protector, heat the body rocker panel moulding assembly LH.

Standard

WARNING:

• Do not touch the heat light and heated parts.
• Touching the heat light may result in burns.
• Touching heated parts for a long time may result in burns.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Heated Part
*b	Heat Light

1. Clean the No. 1 rocker panel moulding protector installation surface with a non-residue solvent.
2. Remove the peeling paper on a new No. 1 rocker panel moulding protector while making sure not to touch the adhesional surface.
3. Install the 2 No. 1 rocker panel moulding protectors in the position shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Mark-off Line

   -

   -

   STANDARD:
   
   

   Area	Specified Condition	Area	Specified Condition
   A	10 mm (0.394 in.)	-	-

   NOTE:

   Press the rear bumper pad firmly to install it.