DTC C1762: Continuous Current to Exhaust Solenoid [08/2021 - ]: Procedure

1. Ask the customer about the vehicle and usage conditions when the DTC was stored.

   HINT: 

   DTC C1762 can be stored under unusual vehicle or usage conditions.

   Points to confirm

   Confirm if there were any foreign objects caught between the body and tires. Confirm if the vehicle has been driven on an unpaved surface or with a wheel not contacting the ground. Confirm if the vehicle height mode has been continuously changed using the height control switch (center cluster module switch RH), causing the vehicle to raise and lower repeatedly.

   Result

   Result
   NEXT

Result: 

NEXT 

See step  2

1. Clear the DTC.

   Refer to DTC CHECK / CLEAR [08/2019 - ]

2. Start the engine and wait for 100 seconds or more.
3. Set the vehicle height to HI, wait until the vehicle height change is complete, and then return the vehicle height to normal.
4. Check for DTC.

   Refer to DTC CHECK / CLEAR [08/2019 - ]

   Result

   Result	Proceed to
   DTC C1762 is output	A
   DTC C1762 is not output	B
   DTC C1762 and other DTCs are output	C

Result: 

B 

END (C1762 WAS OUTPUT DUE TO UNUSUAL VEHICLE OR USAGE CONDITION) 

Result: 

C 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2021 - ] 

Result: 

A 

See step  3

1. Inspect the air tube for clogs.

   Refer to PRECAUTION [08/2015 - ]

   OK

   No clogs are found in the air tube.

   Result

   Result
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE AIR TUBE 

Result: 

OK 

See step  4

1. Turn the engine switch off.
2. Remove the No. 2 height control valve assembly.

   Refer to REMOVAL [08/2015 - ]

3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   1 (LH+) - 2 (E)	15 to 25°C (59 to 77°F)	17.5 to 21.5 Ω
   3 (RH+) - 2 (E)	15 to 25°C (59 to 77°F)	10 to 14 Ω

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (No. 2 Height Control Valve Assembly)

4. Check the leveling solenoid valve.
   1. Connect the positive (+) lead of the battery to terminal 3 (RH+) and the negative (-) lead to terminal 2 (E).
   2. Check the operating sound of the No. 2. height control valve assembly.

      OK

      It makes an operating sound (click).

5. Check the gate solenoid valve.
   1. Connect the positive (+) lead of the battery to terminal 1 (LH+) and the negative (-) lead to terminal 2 (E).
   2. Check the operating sound of the No. 2. height control valve assembly.

      OK

      It makes an operating sound (click).

      Result

      Result
      OK
      NG

Result: 

NG 

REPLACE NO. 2 HEIGHT CONTROL VALVE ASSEMBLY. Refer to  REMOVAL [08/2015 - ] 

Result: 

OK 

See step  5

1. Turn the engine switch off.
2. Remove the height control compressor assembly.

   Refer to REMOVAL [08/2015 - ]

3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   2 (L) - 1 (B)	20°C (68°F)	10 to 14 Ω

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (Exhaust Solenoid Valve)

4. Connect the positive (+) lead of the battery to terminal 2 (L) and the negative (-) lead to terminal 1 (B) of the solenoid valve connector. Then check that the valve makes an operating sound.

   OK

   Operation of solenoid (clicking sound) can be heard.

   Result

   Result
   OK
   NG

Result: 

OK 

REPLACE SUSPENSION CONTROL ECU. Refer to  REMOVAL [08/2015 - ] 

Result: 

NG 

REPLACE HEIGHT CONTROL COMPRESSOR ASSEMBLY. Refer to  REMOVAL [08/2015 - ]