DTC B1244: Light Sensor Circuit [08/2019 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Main Body / Clear DTCs.
5. Clear the DTCs.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Main Body / Trouble Codes.
5. Check for DTCs.

   OK

   DTC B1244 is not output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2019 - 08/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2020 - 08/2021]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2021 - 08/2022]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2022 - ] 

Result: 

NG 

See step  3

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Main Body / Data List.
5. According to the display on the Techstream, read the Data List and check that the value of Light Sensor Illuminance changes while performing the following:
   1. Cover the automatic light control sensor with an opaque object.
   2. Slowly move the opaque object to uncover and then cover the automatic light control sensor.
      MAIN BODY
      
      

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Light Sensor Illuminance	Light control sensor illuminance/ 0 to 8191 lx or SensorFail	Value is output according to ambient light level	-

      OK

      The value changes according to the amount the automatic light control sensor is covered.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [08/2019 - ] 

Result: 

NG 

See step  4

1. Disconnect the H55 automatic light control sensor connector.
2. Disconnect the G117 main body ECU (multiplex network body ECU) connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   H55-1 (CLTB) - G117-19 (CLTB)	Always	Below 1 Ω
   H55-4 (CLTS) - G117-20 (CLTS)	Always	Below 1 Ω
   H55-2 (CLTE) - G117-21 (CLTE)	Always	Below 1 Ω
   H55-1 (CLTB) or G117-19 (CLTB) - Body ground	Always	10 kΩ or higher
   H55-4 (CLTS) or G117-20 (CLTS) - Body ground	Always	10 kΩ or higher
   H55-2 (CLTE) or G117-21 (CLTE) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  5

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   G117-19 (CLTB) - G117-21 (CLTE)	Engine switch off	Below 1 V
   	Engine switch on (IG)	11 to 14 V

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [08/2019 - ] 

Result: 

OK 

See step  6

1. Connect an oscilloscope to the automatic light control sensor connector.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component with harness connected (Automatic Light Control Sensor)

2. Check the waveform.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   OK

   Tester Connection	Tool Setting	Condition	Specified Condition
   H55-4 (CLTS) - H55-2 (CLTE)	2 V/DIV., 10 ms./DIV.	Engine switch on (IG), light control switch in AUTO position	Correct waveform is as shown

   HINT: 

   The communication waveform changes according to the surrounding brightness.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [08/2019 - ] 

Result: 

NG 

REPLACE AUTOMATIC LIGHT CONTROL SENSOR. Refer to  REMOVAL [08/2015 - ]