LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2021 >> ES 350 Luxury >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> Can Communication System (Except Hybrid) - Circuit Tests (1 Of 4) & Diagnostic Codes >> CAN COMMUNICATION SYSTEM (for Gasoline Model) >> Radio Receiver Assembly Communication Stop Mode [09/2022 - ] >> Procedure

Radio Receiver Assembly Communication Stop Mode [09/2022 - ]: Procedure

  1. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      for 12.3 Inch Display A
      for 8 Inch Display B

    Result: 

    B 

    See step  4

    Result: 

    A 

    See step  2

  2. CHECK FOR OPEN IN CAN BUS LINES (RADIO RECEIVER ASSEMBLY BRANCH LINE) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the G146 radio receiver assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G146-13 (CANH) - G146-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      GTY1129041Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Radio Receiver Assembly)

      Result

      Result 
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (RADIO RECEIVER ASSEMBLY) 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) 
    1. Disconnect the G155 radio receiver assembly connector.
    2. Measure the resistance according to the value(s) in the table below.
      GTY1129512Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Radio Receiver Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      G155-1 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
    3. Reconnect the cable to the negative (-) battery terminal.
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      G155-15 (IG) - Body ground Engine switch on (IG) 11 to 14 V
      G155-4 (+B1) - Body ground Always 11 to 14 V
      G155-16 (ACC1) - Body ground Engine switch on (ACC) 11 to 14 V

      Result

      Result 
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [09/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) 

  4. CHECK FOR OPEN IN CAN BUS LINES (RADIO RECEIVER ASSEMBLY BRANCH LINE) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the G147 radio receiver assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G147-13 (CANH) - G147-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      GTY1125744Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Radio Receiver Assembly)

      Result

      Result 
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (RADIO RECEIVER ASSEMBLY) 

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) 
    1. Disconnect the G6 radio receiver assembly connector.
    2. Measure the resistance according to the value(s) in the table below.
      GTY1128005Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Radio Receiver Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      G6-1 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
    3. Reconnect the cable to the negative (-) battery terminal.
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      G6-15 (IG) - Body ground Engine switch on (IG) 11 to 14 V
      G6-4 (+B1) - Body ground Always 11 to 14 V
      G6-16 (ACC1) - Body ground Engine switch on (ACC) 11 to 14 V

      Result

      Result 
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [09/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) 

scientia non olet · About LEMON Manuals