DTC C1614: ECU Malfunction [06/2018 - 09/2022]: Procedure

1. Use the Data List to check if the parking assist ECU status is functioning properly.

   Refer to DATA LIST / ACTIVE TEST [06/2018 - 09/2022]

   Chassis > Circumference Monitoring Camera Control Module > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Main CPU Forced Termination Detection Record	A history item indicating that the main CPU did not enter standby status within 15 seconds of turning the engine switch off and a forced end was applied	No/Yes	No: Parking assist ECU is normal Yes: Parking assist ECU is abnormal	-
   Main CPU Abnormal Response Record	A history item indicating that the main CPU became unresponsive in normal status	No/Yes	No: Parking assist ECU is normal Yes: Parking assist ECU is abnormal	-
   Main CPU Abnormal Reset Record	A history item indicating that the main CPU was reset, although the engine switch was not turned off in normal status	No/Yes	No: Parking assist ECU is normal Yes: Parking assist ECU is abnormal	-
   Image Processing IC Written Protect Record	A history item indicating that the image processing IC memory was write protected	No/Yes	No: Parking assist ECU is normal Yes: Parking assist ECU is abnormal	-
   Image Processing IC Initialized Malfunction Record	A history item indicating that the image processing IC memory was not initialized	No/Yes	No: Parking assist ECU is normal Yes: Parking assist ECU is abnormal	-
   Main EEPROM Access Status	Main EEPROM access status	Normal/Abnormal	Normal: Parking assist ECU is normal Abnormal: Parking assist ECU is abnormal	-
   Sub EEPROM Access Status	Sub-EEPROM access status	Normal/Abnormal	Normal: Parking assist ECU is normal Abnormal: Parking assist ECU is abnormal	-
   System Power Supply Voltage Malfunction Record	A history item indicating an abnormal generated-voltage value from the system power source	No/Yes	No: Parking assist ECU is normal Yes: Parking assist ECU is abnormal	-
   Main CPU Starting Malfunction Record	A history item indicating that the main CPU did not start	No/Yes	No: Parking assist ECU is normal Yes: Parking assist ECU is abnormal	-
   CAN CPU Boot Malfunction Record	A history item indicating that the CPU controlling the input and output of the information obtained via CAN communication did not start and the information could not be retrieved	No/Yes	No: Parking assist ECU is normal Yes: Parking assist ECU is abnormal	-

   Chassis > Circumference Monitoring Camera Control Module > Data List 

   Tester Display
   Main CPU Forced Termination Detection Record
   Main CPU Abnormal Response Record
   Main CPU Abnormal Reset Record
   Image Processing IC Written Protect Record
   Image Processing IC Initialized Malfunction Record
   Main EEPROM Access Status
   Sub EEPROM Access Status
   System Power Supply Voltage Malfunction Record
   Main CPU Starting Malfunction Record
   CAN CPU Boot Malfunction Record

   Result

   Result	Proceed to
   OK is displayed for all items	A
   NG is displayed	B

Result: 

A 

USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ] 

Result: 

B 

See step  2

1. Clear the DTCs.

   Chassis > Circumference Monitoring Camera Control Module > Clear DTCs 

2. Check for DTCs.

   Chassis > Circumference Monitoring Camera Control Module > Trouble Codes 

   OK

   DTC C1614 is not output.

   Result

   Proceed to
   OK
   NG

   HINT: 

   • If DTC C1614 is output, perform the procedure to allow the parking assist ECU to store the vehicle information again.
   • If DTC C1614 is still output after performing the procedure to make the parking assist ECU store the vehicle information 3 times, replace the parking assist ECU.
   • If DTC C1614 is output frequently, replace the parking assist ECU even though the DTC is not output when rechecking for DTCs.

Result: 

OK 

END 

Result: 

NG 

REPLACE PARKING ASSIST ECU. Refer to  REMOVAL [06/2018 - 09/2022]