LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2021 >> ES 350 Luxury >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Anti-Theft Systems >> Door Lock System - Service Information >> Front Door Lock >> Removal [08/2021 - 09/2022] >> Caution / Notice / Hint

Caution / Notice / Hint

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door lock with motor assembly removal/installation are shown below.

NECESSARY PROCEDURE AFTER PARTS REMOVED/INSTALLED/REPLACED (FOR HV MODEL)

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Tracing Assist System Refer to INITIALIZATION [08/2021 - ]
Pre-collision System
Parking Support Brake System (for HV Model)*
Lighting System (for HV Model)
Memorize steering angle neutral point Parking Assist Monitor System (for HV Model) Refer to INITIALIZATION [06/2018 - 09/2022]
Panoramic View Monitor System (for HV Model) Refer to INITIALIZATION [06/2018 - 09/2022]
Initialize power trunk lid system Power Trunk Lid System (for HV Model) Refer to INITIALIZATION [06/2018 - ]
  • Front door glass sub-assembly
  • Front door glass run
Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function
Refer to INITIALIZATION [06/2018 - ]

*: When performing learning using the Techstream.

NOTE:
  • After the power switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System)
  • After the power switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Navigation System)
NECESSARY PROCEDURE AFTER PARTS REMOVED/INSTALLED/REPLACED (FOR GASOLINE MODEL)

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane Tracing Assist System Refer to INITIALIZATION [08/2021 - ]
Pre-collision System
Parking Support Brake System (for Gasoline Model)*
Lighting System (for Gasoline Model)
Memorize steering angle neutral point Parking Assist Monitor System (for Gasoline Model) Refer to INITIALIZATION [06/2018 - 09/2022]
Panoramic View Monitor System (for Gasoline Model) Refer to INITIALIZATION [06/2018 - 09/2022]
Initialize power trunk lid system Power Trunk Lid System (for Gasoline Model) Refer to INITIALIZATION [06/2018 - ]
  • Front door glass sub-assembly
  • Front door glass run
Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function
Refer to INITIALIZATION [06/2018 - ]

*: When performing learning using the Techstream.

NOTE:
  • After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
  • After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

HINT: