DTC B15DB: Telematics Transceiver Disconnected [06/2018 - 10/2019]: Procedure
- CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) POWER SOURCE)
- Disconnect the G10 DCM (telematics transceiver) connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition G10-4 (E) - Body ground Always Below 1 Ω - Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection Condition Specified Condition G10-1 (+B) - G10-4 (E) Power switch off 11 to 14 V G10-8 (ACC) - G10-4 (E) Power switch on (ACC) 11 to 14 V G10-7 (IG2) - G10-4 (E) Power switch on (IG) 11 to 14 V Result
Proceed to OK NG
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 2
- INSPECT RADIO RECEIVER ASSEMBLY
- Disconnect the G2 radio receiver assembly connector.
- Measure the resistance according to the value(s) in the table below.
*a Component without harness connected
(Radio Receiver Assembly)Standard Resistance
Tester Connection Condition Specified Condition G2-11 (USBG) - Body ground Always Below 1 Ω - Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection Condition Specified Condition G2-10 (USBV) - G2-11 (USBG) Power switch on (IG) 4.75 to 5.25 V Result
Proceed to OK NG
Result:
NG
REPLACE RADIO RECEIVER ASSEMBLY. Refer to REMOVAL [06/2018 - 08/2020]
Result:
OK
See step 3
- CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))
- Disconnect the G2 radio receiver assembly connector.
- Disconnect the G109 DCM (telematics transceiver) connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition G2-10 (USBV) - G109-5 (USBV) Always Below 1 Ω G2-11 (USBG) - G109-3 (USBG) Always Below 1 Ω G2-10 (USBV) or G109-5 (USBV) - Body ground Always 10 kΩ or higher G2-11 (USBG) or G109-3 (USBG) - Body ground Always 10 kΩ or higher Result
Proceed to OK NG
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 4
- CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))
- Check the installation condition.
- Check the USB communication lines between the radio receiver assembly and DCM (telematics transceiver) for any installation or connection problems.
- Disconnect the G119 radio receiver assembly connector.
- Disconnect the G109 DCM (telematics transceiver) connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition G119-1 (USB+) - G109-2 (USB+) Always Below 1 Ω G119-2 (USB-) - G109-1 (USB-) Always Below 1 Ω G119-3 (USBS) - G109-6 (USBS) Always Below 1 Ω G119-1 (USB+) or G109-2 (USB+) - Body ground Always 10 kΩ or higher G119-2 (USB-) or G109-1 (USB-) - Body ground Always 10 kΩ or higher G119-3 (USBS) or G109-6 (USBS) - Body ground Always 10 kΩ or higher *a Front view of wire harness connector
(to DCM (telematics transceiver))*b Front view of wire harness connector
(to Radio Receiver Assembly)Result
Proceed to OK NG
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 5
- Check the installation condition.
- REPLACE DCM (TELEMATICS TRANSCEIVER)
- Replace the DCM (telematics transceiver) with a new one.
Refer to REMOVAL [06/2018 - 10/2019]
- Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs
- Turn the power switch off.
- Turn the power switch on (IG) and wait for 90 seconds.
- Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble Codes
OK
No DTCs are output.
Result
Proceed to OK NG
Result:
OK
END
Result:
NG
REPLACE RADIO RECEIVER ASSEMBLY. Refer to REMOVAL [06/2018 - 08/2020]
- Replace the DCM (telematics transceiver) with a new one.