Speedometer Malfunction [06/2018 - ]: Procedure

1. Check if CAN communication DTCs are output.

   Refer to DIAGNOSIS SYSTEM [06/2018 - 10/2019] , or refer to DIAGNOSIS SYSTEM [10/2019 - 08/2020] , or refer to DIAGNOSIS SYSTEM [08/2020 - 08/2021] , or refer to DIAGNOSIS SYSTEM [08/2021 - 09/2022] , or refer to DIAGNOSIS SYSTEM [09/2022 - ]

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ] 

Result: 

A 

See step  2

1. Check if electronically controlled brake system DTCs are output.

   Chassis > ABS/VSC/TRAC > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

Result: 

B 

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM. Refer to  DIAGNOSTIC TROUBLE CODE CHART [06/2018 - 07/2019]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [07/2019 - 08/2020]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2020 - 08/2021]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2021 - ] 

Result: 

A 

See step  3

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Combination Meter / Active Test.
5. Perform the Active Test according to the display on the Techstream.

   Body Electrical > Combination Meter > Active Test 

   Tester Display	Measurement Item	Control Range	Diagnostic Note
   Speed Signal Input (0)	Vehicle speed test signal input (0)*	ON	-
   Speed Signal Input (40)	Vehicle speed test signal input (40)*	ON	The value displayed on the speedometer may deviate. Reference mph: 40 → 39.6 to 42.4 Reference km/h: 40 → 38.8 to 43.3
   Speed Signal Input (80)	Vehicle speed test signal input (80)*	ON	The value displayed on the speedometer may deviate. Reference mph: 80 → 80.4 to 83.6 Reference km/h: 80 → 79.5 to 84.5
   Speed Signal Input (120)	Vehicle speed test signal input (120)*	ON	The value displayed on the speedometer may deviate. Reference mph: 120 → 121.4 to 124.6 Reference km/h: 120 → 120.5 to 125.5
   Speed Signal Input (160)	Vehicle speed test signal input (160)*	ON	The value displayed on the speedometer may deviate. Reference km/h: 160 → 161.5 to 166.5
   Speed Signal Input (200)	Vehicle speed test signal input (200)*	ON	The value displayed on the speedometer may deviate. Reference km/h: 200 → 202.5 to 207.5
   Speed Signal Input (240)	Vehicle speed test signal input (240)*	ON	The value displayed on the speedometer may deviate. Reference km/h: 240 → 243.6 to 248.6

   HINT: 

   • *: When this Active Test is performed, an actual vehicle speed signal is sent via CAN communication to the combination meter assembly to operate the speedometer. The seat belt warning buzzer, etc. may operate when performing this Active Test.

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Speed Signal Input (0)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Speed Signal Input (40)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Speed Signal Input (80)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Speed Signal Input (120)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Speed Signal Input (160)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Speed Signal Input (200)

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Speed Signal Input (240)

   OK

   Speedometer indication is normal.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY). Refer to  REMOVAL [06/2018 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

Result: 

NG 

REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [06/2018 - 08/2021]  , or refer to  REMOVAL [08/2021 - ]