Vehicle Control History [06/2018 - 08/2020]
- DESCRIPTION
- Vehicle Control History is a function that captures and stores ECU data when triggered by specific vehicle behavior.
- It may be possible to determine the cause of the malfunction by checking the vehicle history information and freeze frame data.
- The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.
- The stored data items for Vehicle Control History Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The contents of the Freeze Frame Data is almost the same as that of the Data List.
Refer to DATA LIST / ACTIVE TEST [06/2018 - ]
- PRECAUTIONS
- As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History before performing any inspections.
- As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.
VEHICLE CONTROL HISTORY ITEMCode Tester Display Measurement Item User Notification Diagnostic Note X0451 FL Speed Sensor Wrong Installation History of front speed sensor LH being installed incorrectly - Brake warning light / red (malfunction) illuminates*1
- Brake warning light (yellow) illuminates
- ABS warning light illuminates
- Slip indicator light illuminates
- Brake hold operated indicator light blinks*2
Refer to FL Speed Sensor Wrong Installation (X0451).
Refer to FL Speed Sensor Wrong Installation (X0451) [06/2018 - ]X0452 FR Speed Sensor Wrong Installation History of front speed sensor RH being installed incorrectly - Brake warning light / red (malfunction) illuminates*1
- Brake warning light (yellow) illuminates
- ABS warning light illuminates
- Slip indicator light illuminates
- Brake hold operated indicator light blinks*2
Refer to FR Speed Sensor Wrong Installation (X0452).
Refer to FR Speed Sensor Wrong Installation (X0452) [06/2018 - ]X0453 RL Speed Sensor Wrong Installation History of rear speed sensor LH being installed incorrectly - Brake warning light / red (malfunction) illuminates*1
- Brake warning light (yellow) illuminates
- ABS warning light illuminates
- Slip indicator light illuminates
- Brake hold operated indicator light blinks*2
Refer to RL Speed Sensor Wrong Installation (X0453).
Refer to RL Speed Sensor Wrong Installation (X0453) [06/2018 - 08/2020]X0454 RR Speed Sensor Wrong Installation History of rear speed sensor RH being installed incorrectly - Brake warning light / red (malfunction) illuminates*1
- Brake warning light (yellow) illuminates
- ABS warning light illuminates
- Slip indicator light illuminates
- Brake hold operated indicator light blinks*2
Refer to RR Speed Sensor Wrong Installation (X0454).
Refer to RR Speed Sensor Wrong Installation (X0454) [06/2018 - 08/2020]X0455 Steering Angle Sensor Wrong Installation History of steering angle sensor being installed incorrectly - Slip indicator light illuminates
- Brake hold operated indicator light blinks*2
- X0456 Yaw Rate Sensor Wrong Installation History of yaw rate sensor (airbag ECU assembly) being installed incorrectly - Slip indicator light illuminates
- Brake hold operated indicator light blinks*2
Refer to Yaw Rate Sensor Wrong Installation (X0456).
Refer to Yaw Rate Sensor Wrong Installation (X0456) [06/2018 - ]X2079 Communication Error from Brake Control Module to Engine Control Module History of receiving an invalid communication signal from ECM - Brake warning light (yellow) illuminates
- Slip indicator light illuminates
- Brake hold operated indicator light blinks*2
- Using the Techstrem, perform a Health Check.
- Refer to the flow chart(s) for the output DTCs.
X2086 SRS Airbag Malfunction History of receiving an abnormal secondary collision brake control request signal from airbag ECU assembly - Refer to How to Proceed with Troubleshooting in Airbag System.
Refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ]X2087 Engine Malfunction History of receiving an SFI system abnormal signal from ECM - Slip indicator light illuminates
- Brake warning light (yellow) illuminates
- Brake hold operated indicator light blinks*2
Refer to How to Proceed with Troubleshooting in SFI System.
Refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ]X208A Zero Point Calibration of Steering Angle Sensor Initialization Malfunction History of failure in acquiring steering angle zero point even after the vehicle is driven in a straight line at a vehicle speed of 15 km/h (9 mph) or more for 115 seconds or more with the steering angle sensor zero point calibration cleared - Slip indicator light illuminates
- Brake hold operated indicator light blinks*2
Refer to Zero Point Calibration of Steering Angle Sensor Initialization Malfunction (X208A).
Refer to Zero Point Calibration of Steering Angle Sensor Initialization Malfunction (X208A) [06/2018 - ]X208B EPB Motor Continuous Operation Request History of system suspended to prevent overheat of parking brake actuator assembly when electric parking brake was used repeatedly - Brake hold operated indicator light blinks*2
- Parking brake indicator light (red) blinks
- EPB: Electric Parking Brake System
- Explain that system was suspended to prevent overheating of parking brake actuator assembly when electric parking brake was used repeatedly.
X2096 Pre-Collision Brake History of pre-collision brake operation In accordance with Pre-collision System behavior - X2098 Pre-Collision Brake Assist History of pre-collision brake assist operation In accordance with Pre-collision System behavior - X20A0 ABS History of ABS operation - - X20A1 VSC History of VSC operation Slip indicator light blinks - X20A2 TRC(TRAC) History of TRAC operation Slip indicator light blinks - X20A5 Hill Start Assist History of hill start assist operation - - X20A7 Brake Assist History of brake assist operation - - X20A8 Secondary Collision Brake History of secondary collision brake operation - - X20A9 ABS Continuous Operation Request History of ABS being operated for 60 seconds or more - Brake warning light / red (malfunction) illuminates*1
- ABS warning light illuminates
- Slip indicator light illuminates
- Brake hold operated indicator light blinks*2
- X20AA VSC Continuous Operation Request History of VSC being operated for 10 seconds or more - Brake warning light / red (malfunction) illuminates*1
- ABS warning light illuminates
- Slip indicator light illuminates
- Brake hold operated indicator light blinks*2
- - *1: The brake warning light / red (malfunction) illuminates when any of the following vehicle conditions are met:
- When EBD is prohibited
- When a malfunction has occurred
- When failure compensation control is prohibited
- *2: When the vehicle is put into the following vehicle conditions and the brake hold switch (electric parking brake switch assembly) is turned on, the brake hold operation light blinks.
- Conditions required for operation standby:
- The driver door is closed.
- The driver seat belt is fastened.
- Conditions required for operation standby:
- CHECK VEHICLE CONTROL HISTORY (ELECTRONICALLY CONTROLLED BRAKE SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM)
- CLEAR VEHICLE CONTROL HISTORY (ELECTRONICALLY CONTROLLED BRAKE SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM)
- Turn the engine switch off.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Chassis / Brake/EPB / Utility / Vehicle Control History (RoB).
Chassis > Brake/EPB > Utility
Tester Display Vehicle Control History (RoB) - Press the DTC clear button.NOTE:
By performing this procedure, all stored Vehicle Control History items will be cleared.
- VEHICLE CONTROL HISTORY (AIRBAG SYSTEM)
HINT:
A part of the control history can be confirmed using the vehicle control history.
Refer to VEHICLE CONTROL HISTORY [06/2018 - ]