DTC C0512-23: Right Rear Wheel Speed Sensor Signal Stuck Low [08/2020 - ]: Procedure
- CHECK FREEZE FRAME DATA (WHEEL SPEED)
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
- Select a DTC to display the Freeze Frame Data.
- Read the freeze frame data of DTC C0512-23.
Chassis > Brake/EPB
Tester Display Measurement Item Range Normal Condition Diagnostic Note FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations Chassis > Brake/EPB > DTC(C0512-23) > Freeze Frame Data
Tester Display FR Wheel Speed FL Wheel Speed RR Wheel Speed RL Wheel Speed Result
Result Proceed to The value of RR Wheel Speed is 2 km/h (1 mph) or less when all other values are 12 km/h (7 mph) or more. A The value of RR Wheel Speed is 2 km/h (1 mph) or less when all other values are 43 km/h (27 mph) or more. (for 2WD) B The value of RR Wheel Speed is 2 km/h (1 mph) or less when all other values are 43 km/h (27 mph) or more. (for AWD) C
Result:
B
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH. Refer to REMOVAL [06/2018 - 08/2021] , or refer to REMOVAL [08/2021 - 09/2022] , or refer to REMOVAL [09/2022 - ]
Result:
C
See step 3
Result:
A
See step 2
- READ VALUE USING TECHSTREAM (RR WHEEL SPEED)
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Enter the following menus: Chassis / Brake/EPB / Data List.
Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations Chassis > Brake/EPB > Data List
Tester Display RR Wheel Speed - Start the engine and perform a road test.
- Check that the value of RR Wheel Speed changes in accordance with vehicle speed when accelerating from 0 km/h to 20 km/h (0 mph to 12 mph).
OK
The value of RR Wheel Speed changes in accordance with vehicle speed.
HINT:
If the result of the road test is within the specified range, it is possible that this DTC was stored due to a particular situation such as brake drag, wheelspin or wheel lockup.
Result
Result Proceed to OK A NG (for 2WD) B NG (for AWD) C
Result:
A
USE SIMULATION METHOD TO CHECK. Refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ]
Result:
B
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH. Refer to REMOVAL [06/2018 - 08/2021] , or refer to REMOVAL [08/2021 - 09/2022] , or refer to REMOVAL [09/2022 - ]
Result:
C
See step 3
- CHECK REAR SPEED SENSOR RH INSTALLATION
- Check the rear speed sensor RH installation.
*1 Rear Speed Sensor RH *a Correct *b Incorrect *c 8.5 N.m *d No clearance OK
There is no clearance between the rear speed sensor RH and the rear axle carrier RH.
The installation bolt is tightened properly.
Torque
8.5 N.m (87 kgf/cm, 75 in.lbf)
Result
Proceed to OK NG
Result:
OK
REPLACE REAR SPEED SENSOR RH. Refer to REMOVAL [08/2020 - ]
Result:
NG
REINSTALL OR REPLACE REAR SPEED SENSOR RH. Refer to INSTALLATION [08/2020 - ]
- Check the rear speed sensor RH installation.