Abnormal Brake Pedal Response on First Depression [10/2018 - ]: Procedure

1. Check the conditions at the time the problem occurred.
   1. Whether a warning light illuminated or the buzzer sounded.
   2. The number of times the power switch was turned on (IG) since the latest symptom occurred.
   3. Frequency of the symptom.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  2

1. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [10/2018 - ]

   Chassis > ABS/VSC/TRAC > Clear DTCs 

2. Turn the power switch off.
3. Turn the power switch on (IG).
4. Check the DTCs (electronically controlled brake system) that are output.

   Refer to DTC CHECK / CLEAR [10/2018 - ]

   Chassis > ABS/VSC/TRAC > Trouble Codes 

   Result

   Result	Proceed to
   DTCs C1391 and C1256 are not output.	A
   DTCs C1391 and/or C1256 are output.	B

Result: 

B 

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS. Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2018 - 08/2021]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2021 - 07/2022]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [07/2022 - ] 

Result: 

A 

See step  3

1. Turn the power switch off.
2. Depress the brake pedal within 2 minutes of opening the driver door and check the response of the brake pedal.
3. Release the brake pedal and wait for 2 minutes without depressing the brake pedal, opening or closing the driver door or operating the power switch.
4. After 2 seconds or more have elapsed, depress the brake pedal and check that the first depression response is different to successive depression responses.

   HINT: 

   Compare the response of the brake pedal when the system is in sleep mode and when the stroke simulator is operating.

   Result

   Result	Proceed to
   The response of the brake pedal does not change.	A
   The response of the brake pedal changed.	B

Result: 

B 

END 

Result: 

A 

See step  4

1. Set the interior light door switch to ON and check that the map light assembly illuminates, then set the interior light door switch to DOOR.
2. Check that the map light assembly illuminates when the driver door is opened.

   OK

   The map light assembly illuminates when the driver door is opened.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

INSPECT LIGHTING SYSTEM (COURTESY LIGHT SWITCH CIRCUIT). Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2018 - 07/2022]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [07/2022 - ] 

Result: 

OK 

See step  5

1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

   OK

   The connector is securely connected.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Front view of wire harness connector (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

2. Disconnect the A37 skid control ECU (brake booster with master cylinder assembly) connector.
3. Check both the connector case and the terminals for deformation and corrosion.

   OK

   No deformation or corrosion.

4. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   A37-24 (CTY) - Body ground	Driver door open	1.5 V or less
   A37-24 (CTY) - Body ground	Driver door closed	11 to 14 V

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY. Refer to  REMOVAL [10/2018 - 07/2022]  , or refer to  REMOVAL [07/2022 - ] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR (CTY CIRCUIT)