LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> UX 200 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 7 (Electric Parking Brake System (Diagnostics - Introduction) (Hybrid)) >> ELECTRIC PARKING BRAKE SYSTEM (for HV Model) >> How To Proceed With Troubleshooting [08/2021 - ] >> Procedure

How To Proceed With Troubleshooting [08/2021 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus UX 250h, 2023 Lexus UX 250h, 2022 Lexus UX 250h, 2021 Lexus UX 250h, and 2020 Lexus UX 250h. However, it is still accessible from the selected car via links, so may be relevant.
  1. VEHICLE BROUGHT TO WORKSHOP 

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    See step  2

  2. CUSTOMER PROBLEM ANALYSIS 
    1. Interview the customer and confirm the problem.

      Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2018 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  3

  3. INSPECT AUXILIARY BATTERY VOLTAGE 

    Standard Voltage

    11 to 14 V

    1. If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    See step  4

  4. CHECK DTC AND FREEZE FRAME DATA* 
    1. Check and record DTCs and freeze frame data.

      Chassis > Electric Parking Brake > Trouble Codes 

    2. Clear the DTCs and freeze frame data.

      Chassis > Electric Parking Brake > Clear DTCs 

    3. Recheck for DTCs.
      1. Reconfirm the DTCs based on the recorded DTCs and freeze frame data.

        Chassis > Electric Parking Brake > Trouble Codes 

      2. Try to reproduce the problem symptoms based on the recorded DTCs and freeze frame data, and then check if the DTCs are output again.

      Result

      Result Proceed to
      DTCs are not output (Problem symptom occurs.) A
      DTCs are output B
      DTCs are not output (Problem symptom does not occur.) C

      HINT: 

      • Refer to Diagnostic Trouble Code Chart if any DTCs are output.
      • When DTCs indicating a CAN communication system malfunction are output, first troubleshoot and repair the CAN communication system.

    Result: 

    GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2021 - 07/2022]  Refer to  DIAGNOSTIC TROUBLE CODE CHART [07/2022 - ]  

    Result: 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2018 - ] 

    Result: 

    See step  5

  5. PROBLEM SYMPTOMS TABLE 
    1. Proceed to Problem Symptoms Table.

      Refer to PROBLEM SYMPTOMS TABLE [08/2021 - ] 

      Result

      Result Proceed to
      Fault is not listed in Problem Symptoms Table A
      Fault is listed in Problem Symptoms Table B

    Result: 

    See step  7

    Result: 

    See step  6

  6. OVERALL ANALYSIS AND TROUBLESHOOTING* 
    1. Refer to Terminals of ECU.

      Refer to TERMINALS OF ECU [08/2021 - ] 

    2. Refer to Data List / Active Test.

      Refer to DATA LIST / ACTIVE TEST [08/2021 - ] 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  7

  7. REPAIR OR REPLACE 

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    See step  8

  8. CONFIRMATION TEST 

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    END