LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> UX 200 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 44 (Hybrid Control System (Diagnostic Codes (5 Of 5) & Circuit Tests)) >> Hybrid Control System >> Brake Override System [10/2018 - ] >> Procedure

Brake Override System [10/2018 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus UX 250h, 2023 Lexus UX 250h, 2022 Lexus UX 250h, 2021 Lexus UX 250h, and 2020 Lexus UX 250h. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DTC OUTPUT (HEALTH CHECK) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: System Select / Health Check.
    5. Check for DTCs.

      Result

      Result Proceed to
      No DTCs are output. A
      DTCs are output. B
    6. Turn the power switch off.

    Result: 

    B 

    GO TO DTC CHART Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2018 - ] 

    Result: 

    A 

    See step  2

  2. READ VALUE USING TECHSTREAM (MASTER CYLINDER CONTROL TORQUE) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (READY).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Hybrid Control / Data List / Master Cylinder Control Torque.

      Powertrain > Hybrid Control > Data List 

      Tester Display
      Master Cylinder Control Torque
    5. Read the value displayed on the Techstream.

      Result

      Result Proceed to
      Display changes according to brake pedal depression force A
      Other than above B
    6. Turn the power switch off.

    Result: 

    B 

    CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY. Refer to  ON-VEHICLE INSPECTION [10/2018 - ] 

    Result: 

    A 

    See step  3

  3. READ VALUE USING TECHSTREAM (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %) 

    Refer to ON-VEHICLE INSPECTION [10/2018 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY. Refer to  REMOVAL [10/2018 - ] 

    Result: 

    OK 

    See step  4

  4. READ VALUE USING TECHSTREAM (VEHICLE SPEED) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Hybrid Control / Data List / Vehicle Speed.

      Powertrain > Hybrid Control > Data List 

      Tester Display
      Vehicle Speed
    5. Read the value of "Vehicle Speed" displayed on the Techstream.

      Standard

      Inspection Condition Specified Condition
      Vehicle stopped 0 km/h (0 mph)
      Vehicle being driven at a constant speed
      (16 to 64 km/h (10 to 40 mph))      		 No large fluctuations in displayed speed
      WARNING:

      Perform this road test only in an appropriate safe location, in accordance with all local laws.

      HINT: 

      Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.

    6. Turn the power switch off.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT). Refer to  Speed Signal Circuit [10/2018 - 07/2022]  Refer to  Speed Signal Circuit [07/2022 - ] 

    Result: 

    OK 

    See step  5

  5. READ VALUE USING TECHSTREAM (FR, FL, RR, RL WHEEL SPEED) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (READY).
    3. Turn the Techstream on.
    4. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List / All Data / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.

      Chassis > ABS/VSC/TRAC > Data List 

      Tester Display
      FR Wheel Speed
      FL Wheel Speed
      RR Wheel Speed
      RL Wheel Speed
    5. Read the value of "FR Wheel Speed", "FL Wheel Speed", "RR Wheel Speed" and "RL Wheel Speed" displayed on the Techstream.

      Standard

      Inspection Condition Specified Condition
      Vehicle stopped 0 km/h (0 mph)
      Vehicle being driven at a constant speed
      (16 to 64 km/h (10 to 40 mph))      		 No large fluctuations in displayed speed
      WARNING:

      Perform this road test only in an appropriate safe location, in accordance with all local laws.

      HINT: 

      Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.

    6. Turn the power switch off.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    INSPECT FRONT OR REAR SPEED SENSOR. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2018 - ] 

scientia non olet · About LEMON Manuals