LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> UX 200 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 43 (Hybrid Battery Control System (Service Information) (2 Of 2)) >> HV Relay Assembly >> Inspection [10/2018 - ] >> Procedure

Inspection [10/2018 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus UX 250h, 2023 Lexus UX 250h, 2022 Lexus UX 250h, 2021 Lexus UX 250h, and 2020 Lexus UX 250h. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY 
    1. Inspect SMRB:
      1. Measure the resistance according to the value(s) in the table below.
        GTY804475Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (HV Battery Junction Block Assembly)        		 - -

        Standard Resistance

        Tester Connection Condition Specified Condition
        W4-1 (CBI) - Z15-1 (+) Auxiliary battery voltage not applied between terminals N41-1 (SMRB) and N41-3 (GND) 10 kΩ or higher
        Auxiliary battery voltage applied between terminals N41-1 (SMRB) and N41-3 (GND) Below 1 Ω
      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        N41-1 (SMRB) - N41-3 (GND) -40 to 80°C (-40 to 176°F) 20.6 to 40.8 Ω

        If the result is not as specified, replace the HV battery junction block assembly.

    2. Inspect SMRG:
      1. Measure the resistance according to the value(s) in the table below.
        GTY804476Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (HV Battery Junction Block Assembly)        		 - -

        Standard Resistance

        Tester Connection Condition Specified Condition
        W3-1 (CEI) - Z17-1 (-) Auxiliary battery voltage not applied between terminals N41-4 (SMRG) and N41-3 (GND) 10 kΩ or higher
        Auxiliary battery voltage applied between terminals N41-4 (SMRG) and N41-3 (GND) Below 1 Ω
      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        N41-4 (SMRG) - N41-3 (GND) -40 to 80°C (-40 to 176°F) 20.6 to 40.8 Ω

        If the result is not as specified, replace the HV battery junction block assembly.

    3. Inspect SMRP:
      1. Measure the resistance according to the value(s) in the table below.
        GTY804474Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (HV Battery Junction Block Assembly)        		 - -

        Standard Resistance

        Tester Connection Condition Specified Condition
        W3-1 (CEI) - Z17-1 (-) Auxiliary battery voltage applied between terminals N41-2 (SMRP) and N41-3 (GND) 10 kΩ or higher
        Auxiliary battery voltage applied between terminals N41-2 (SMRP) and N41-3 (GND) 24.3 and 29.7 Ω
      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        N41-2 (SMRP) - N41-3 (GND) -40 to 80°C (-40 to 176°F) 140 to 290 Ω

        If the result is not as specified, replace the HV battery junction block assembly.

scientia non olet · About LEMON Manuals