Ignition Circuit [10/2018 - ]: Procedure
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus UX 250h, 2023 Lexus UX 250h, 2022 Lexus UX 250h, 2021 Lexus UX 250h, and 2020 Lexus UX 250h. However, it is still accessible from the selected car via links, so may be relevant.
- CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
*a Front view of wire harness connector
(to Ignition Coil Assembly)- Disconnect the ignition coil assembly connectors.
- Turn the power switch on (IG).
- Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection Condition Specified Condition C1-1 (+B) - C1-3 (GND) Power switch on (IG) 11 to 14 V C2-1 (+B) - C2-3 (GND) Power switch on (IG) 11 to 14 V C3-1 (+B) - C3-3 (GND) Power switch on (IG) 11 to 14 V C4-1 (+B) - C4-3 (GND) Power switch on (IG) 11 to 14 V Result
Proceed to OK NG
Result:
NG
See step 3
Result:
OK
See step 2
- CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
- Disconnect the ignition coil assembly connectors.
- Disconnect the ECM connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition C1-2 (IGT1) - C34-49 (IGT1) Always Below 1 Ω C2-2 (IGT2) - C34-48 (IGT2) Always Below 1 Ω C3-2 (IGT3) - C34-47 (IGT3) Always Below 1 Ω C4-2 (IGT4) - C34-46 (IGT4) Always Below 1 Ω C1-2 (IGT1) or C34-49 (IGT1) - Body ground and other terminals Always 10 kΩ or higher C2-2 (IGT2) or C34-48 (IGT2) - Body ground and other terminals Always 10 kΩ or higher C3-2 (IGT3) or C34-47 (IGT3) - Body ground and other terminals Always 10 kΩ or higher C4-2 (IGT4) or C34-46 (IGT4) - Body ground and other terminals Always 10 kΩ or higher Result
Proceed to OK NG
Result:
OK
REPLACE ECM. Refer to REMOVAL [10/2018 - 07/2022] Refer to REMOVAL [07/2022 - ]
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
- CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
- Disconnect the ignition coil assembly connectors.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition C1-3 (GND) - Body ground Always Below 1 Ω C2-3 (GND) - Body ground Always Below 1 Ω C3-3 (GND) - Body ground Always Below 1 Ω C4-3 (GND) - Body ground Always Below 1 Ω Result
Proceed to OK NG
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 4
- CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - IGNITION COIL ASSEMBLY)
- Disconnect the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.
- Disconnect the ignition coil assembly connectors.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition 2A-9 - C1-1 (+B) Always Below 1 Ω 2A-9 - C2-1 (+B) Always Below 1 Ω 2A-9 - C3-1 (+B) Always Below 1 Ω 2A-9 - C4-1 (+B) Always Below 1 Ω 2A-9 or C1-1 (+B) - Body ground and other terminals Always 10 kΩ or higher 2A-9 or C2-1 (+B) - Body ground and other terminals Always 10 kΩ or higher 2A-9 or C3-1 (+B) - Body ground and other terminals Always 10 kΩ or higher 2A-9 or C4-1 (+B) - Body ground and other terminals Always 10 kΩ or higher Result
Proceed to OK NG
Result:
OK
GO TO ECM POWER SOURCE CIRCUIT. Refer to ECM Power Source Circuit [10/2018 - ]
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR