Customize Parameters [10/2018 - ]
- CUSTOMIZE HEADUP DISPLAY SYSTEM NOTE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
HINT:
The following items can be customized.
- Customizing with the Techstream
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Enter the following menus: Customize Setting / Display.
- Select the setting by referring to the table below.
Display
Tester Display Description Default Setting ECU Projection Adjustment (Tilt) Headup display image calibration (tilt calibration)* Default $03:Clockwise (+3),$02:Clockwise (+2),$01:Clockwise (+1),$00:Default,$FF:Anti-Clockwise (-1),$FE:Anti-Clockwise (-2),$FD:Anti-Clockwise (-3) Meter mirror sub-assembly Projection Adjustment (Keystone) Headup display image calibration (keystone calibration) Default $03:Narrow Top (+3),$02:Narrow Top (+2),$01:Narrow Top (+1),$00:Default,$FF:Narrow Bottom (-1),$FE:Narrow Bottom (-2),$FD:Narrow Bottom (-3) Meter mirror sub-assembly Projection Adjustment (Distortion) Headup display image calibration (distortion calibration) Default $03:Convex (+3),$02:Convex (+2),$01:Convex (+1),$00:Default,$FF:Concave (-1),$FE:Concave (-2),$FD:Concave (-3) Meter mirror sub-assembly Audio Information Display Function Audio system operation status display setting for headup display* ON $00:OFF,$01:ON Meter mirror sub-assembly Master Caution Display Function Master warning light display setting for headup display ON $00:OFF,$01:ON Meter mirror sub-assembly Speed Limit Display Function Speed limit display setting for headup display ON $00:OFF,$01:ON Meter mirror sub-assembly Turn by Turn Animation Function Route guidance to destination display setting for headup display* ON $00:OFF,$01:ON Meter mirror sub-assembly Traffic Sign Recognition Animation Function Traffic sign recognition display setting for headup display* ON $00:OFF,$01:ON Meter mirror sub-assembly Memory Call Link Function Memory call link setting for headup display image position ON $00:OFF,$01:ON Meter mirror sub-assembly Seat Switch Link Function Power seat switch link setting for headup display image position ON $00:OFF,$01:ON Meter mirror sub-assembly ECO Drive Indicator Zone Display Function ECO driving indicator zone display setting for headup display ON $00:OFF,$01:ON Meter mirror sub-assembly Projection Adjustment (Tilt) Headup display image calibration (tilt calibration) Default $05:Clockwise (+5),$04:Clockwise (+4),$03:Clockwise (+3),$02:Clockwise (+2),$01:Clockwise (+1),$00:Default,$FF:Anti-Clockwise (-1),$FE:Anti-Clockwise (-2),$FD:A**cut** Meter mirror sub-assembly HINT:
- Depending on the specifications of the vehicle, some items may not be displayed.
- *: Not applicable to this vehicle
- Customizing with the multi-information display
- Turn the ignition switch to ON.
- Select the settings tab on the multi-information display and set the customize settings.
Display Detail Description Setting ECU HUD Brightness/Position Brightness Brightness setting for headup display - Meter mirror sub-assembly Position Position setting for headup display - Vehicle Settings HUD Tachometer Settings Display setting for headup display Display setting for headup display Blank/Hybrid System/Tachometer/Eco Indicator Meter mirror sub-assembly HUD Driving Support Navigation Display setting for headup display On/Off Driving Assist Display setting for headup display On/Off Compass Display setting for headup display On/Off Audio Display setting for headup display On/Off Lane Display setting for headup display On/Off HUD Rotation Headup display image calibration (rotation calibration) - HINT:
Depending on the specifications of the vehicle, some items may not be displayed.