DTC B15C3: Speaker Output Short [08/2019 - ]: Procedure

1. Disconnect the J66 stereo component amplifier assembly connector.
2. Disconnect the K2 front No. 3 speaker assembly connector.
3. Disconnect the K6 and K8 front No. 2 speaker assembly connectors (for 9 Speakers).

   Disconnect the K5 and K7 front No. 2 speaker assembly connectors (except 9 Speakers).

4. Disconnect the M3 and N3 front No. 1 speaker assembly connectors.
5. Disconnect the O5 and P5 rear No. 2 speaker assembly connectors.
6. Disconnect the S53 rear No. 3 speaker assembly connector (except 9 Speakers).
7. Disconnect the R25 and S38 quarter side speaker assembly connectors (for 15 Speakers).
8. Measure the resistance between the stereo component amplifier assembly or the speakers and body ground to check for a short in the wire harness.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   J66-7 (CTR+) or K2-2 - Body ground	Always	10 kΩ or higher
   J66-22 (CTR-) or K2-1 - Body ground	Always	10 kΩ or higher
   J66-13 (FR+) or K6-4 - Body ground*1 J66-13 (FR+) or K5-2 - Body ground*2	Always	10 kΩ or higher
   J66-28 (FR-) or K6-2 - Body ground*1 J66-28 (FR-) or K5-1 - Body ground*2	Always	10 kΩ or higher
   J66-12 (FL+) or K8-4 - Body ground*1 J66-12 (FL+) or K7-2 - Body ground*2	Always	10 kΩ or higher
   J66-27 (FL-) or K8-2 - Body ground*1 J66-27 (FL-) or K7-1 - Body ground*2	Always	10 kΩ or higher
   J66-5 (WFR+) or M3-1 - Body ground	Always	10 kΩ or higher
   J66-20 (WFR-) or M3-2 - Body ground	Always	10 kΩ or higher
   J66-4 (WFL+) or N3-1 - Body ground	Always	10 kΩ or higher
   J66-19 (WFL-) or N3-2 - Body ground	Always	10 kΩ or higher
   J66-9 (RR+) or O5-4 (+TW) - Body ground	Always	10 kΩ or higher
   J66-24 (RR-) or O5-2 (-TW) - Body ground	Always	10 kΩ or higher
   J66-8 (RL+) or P5-4 (+TW) - Body ground	Always	10 kΩ or higher
   J66-23 (RL-) or P5-2 (-TW) - Body ground	Always	10 kΩ or higher
   J66-6 (WF1+) or S53-1 - Body ground*2	Always	10 kΩ or higher
   J66-21 (WF1-) or S53-2 - Body ground*2	Always	10 kΩ or higher
   J66-11 (SR+) or R25-2 - Body ground*3	Always	10 kΩ or higher
   J66-26 (SR-) or R25-1 - Body ground*3	Always	10 kΩ or higher
   J66-10 (SL+) or S38-2 - Body ground*3	Always	10 kΩ or higher
   J66-25 (SL-) or S38-1 - Body ground*3	Always	10 kΩ or higher

   1. *1: for 9 Speakers
   2. *2: except 9 Speakers
   3. *3: for 15 Speakers

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  2

1. Disconnect the O2 and P2 rear speaker assembly connectors.
2. Disconnect the O5 and P5 rear No. 2 speaker assembly connectors.
3. Measure the resistance between the rear speaker assembly or the rear No. 2 speaker assembly and body ground to check for a short in the wire harness.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   O2-1 or O5-3 (+) - Body ground	Always	10 kΩ or higher
   O2-2 or O5-1 (-) - Body ground	Always	10 kΩ or higher
   P2-1 or P5-3 (+) - Body ground	Always	10 kΩ or higher
   P2-2 or P5-1 (-) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  3

1. Choose the model to be inspected.

   Result

   Result	Proceed to
   except 15 Speakers	A
   for 15 Speakers	B

Result: 

B 

See step  5

Result: 

A 

See step  4

1. Remove the front No. 3 speaker assembly.

   Refer to REMOVAL [10/2015 - ]

2. Inspect the front No. 3 speaker assembly.

   Refer to INSPECTION [10/2015 - ]

   Result

   Proceed to
   OK
   NG

Result: 

OK 

See step  6

Result: 

NG 

REPLACE FRONT NO. 3 SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

1. Remove the front No. 3 speaker assembly.

   Refer to REMOVAL [10/2015 - ]

2. Inspect the front No. 3 speaker assembly.

   Refer to INSPECTION [10/2015 - ]

3. Clear the DTCs.

   Body Electrical > Navigation System > Clear DTCs 

4. Recheck for DTCs and check that no DTCs are output.

   Body Electrical > Navigation System > Trouble Codes 

   OK

   No DTCs are output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END 

Result: 

NG 

See step  6

1. Remove the front No. 2 speaker assembly.

   Refer to REMOVAL [10/2015 - ]

2. Inspect the front No. 2 speaker assembly.

   Refer to INSPECTION [10/2015 - ]

3. Clear the DTCs.

   Body Electrical > Navigation System > Clear DTCs 

4. Recheck for DTCs and check that no DTCs are output.

   Body Electrical > Navigation System > Trouble Codes 

   OK

   No DTCs are output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END 

Result: 

NG 

See step  7

1. Remove the front No. 1 speaker assembly.

   Refer to REMOVAL [10/2015 - ]

2. Inspect the front No. 1 speaker assembly.

   Refer to INSPECTION [10/2015 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

Result: 

OK 

See step  8

1. Remove the rear speaker assembly.

   Refer to REMOVAL [10/2015 - ]

2. Inspect the rear speaker assembly.

   Refer to INSPECTION [10/2015 - ]

   Result

   Result	Proceed to
   OK (for 9 Speakers)	A
   OK (except 9 Speakers)	B
   NG	C

Result: 

B 

See step  10

Result: 

C 

REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

Result: 

A 

See step  9

1. Remove the rear No. 2 speaker assembly.

   Refer to REMOVAL [10/2015 - ]

2. Inspect the rear No. 2 speaker assembly.

   Refer to INSPECTION [10/2015 - ]

3. Clear the DTCs.

   Body Electrical > Navigation System > Clear DTCs 

4. Recheck for DTCs and check that no DTCs are output.

   Body Electrical > Navigation System > Trouble Codes 

   OK

   No DTCs are output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END 

Result: 

NG 

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY. Refer to  REMOVAL [08/2019 - ] 

1. Remove the rear No. 2 speaker assembly.

   Refer to REMOVAL [10/2015 - ]

2. Inspect the rear No. 2 speaker assembly.

   Refer to INSPECTION [10/2015 - ]

3. Clear the DTCs.

   Body Electrical > Navigation System > Clear DTCs 

4. Recheck for DTCs and check that no DTCs are output.

   Body Electrical > Navigation System > Trouble Codes 

   OK

   No DTCs are output.

   Result

   Result	Proceed to
   OK	A
   NG (for 12 Speakers)	B
   NG (for 15 Speakers)	C

Result: 

A 

END 

Result: 

C 

See step  12

Result: 

B 

See step  11

1. Remove the rear No. 3 speaker assembly.

   w/o Rear No. 2 Seat: Refer to REMOVAL [08/2019 - ]

   w/ Rear No. 2 Seat: Refer to REMOVAL [03/2018 - ]

2. Inspect the rear No. 3 speaker assembly.

   w/o Rear No. 2 Seat: Refer to INSPECTION [10/2015 - ]

   w/ Rear No. 2 Seat: Refer to INSPECTION [03/2018 - ]

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY. Refer to  REMOVAL [08/2019 - ] 

Result: 

NG 

REPLACE REAR NO. 3 SPEAKER ASSEMBLY 

w/o Rear No. 2 Seat: Refer to REMOVAL [08/2019 - ]

w/ Rear No. 2 Seat: Refer to REMOVAL [03/2018 - ]

1. Remove the rear No. 3 speaker assembly.

   w/o Rear No. 2 Seat: Refer to REMOVAL [08/2019 - ]

   w/ Rear No. 2 Seat: Refer to REMOVAL [03/2018 - ]

2. Inspect the rear No. 3 speaker assembly.

   w/o Rear No. 2 Seat: Refer to INSPECTION [10/2015 - ]

   w/ Rear No. 2 Seat: Refer to INSPECTION [03/2018 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE REAR NO. 3 SPEAKER ASSEMBLY 

w/o Rear No. 2 Seat: Refer to REMOVAL [08/2019 - ]

w/ Rear No. 2 Seat: Refer to REMOVAL [03/2018 - ]

Result: 

OK 

See step  13

1. Remove the quarter side speaker assembly.

   w/o Rear No. 2 Seat: Refer to REMOVAL [08/2019 - ]

   w/ Rear No. 2 Seat: Refer to REMOVAL [03/2018 - ]

2. Inspect the quarter side speaker assembly.

   w/o Rear No. 2 Seat: Refer to INSPECTION [10/2015 - ]

   w/ Rear No. 2 Seat: Refer to INSPECTION [03/2018 - ]

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY. Refer to  REMOVAL [08/2019 - ] 

Result: 

NG 

REPLACE QUARTER SIDE SPEAKER ASSEMBLY 

w/o Rear No. 2 Seat: Refer to REMOVAL [08/2019 - ]

w/ Rear No. 2 Seat: Refer to REMOVAL [03/2018 - ]