LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> RX 350L FWD >> Repair and Diagnosis >> Electrical >> Gauges >> Meter / Gauge / Display - Service Information >> Combination Meter >> Removal [08/2016 - 08/2019] >> Procedure

Removal [08/2016 - 08/2019]: Procedure

  1. PRECAUTION 
    NOTE:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Refer to PRECAUTION [09/2015 - 12/2017] , or refer to PRECAUTION [12/2017 - 08/2019]

  2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS 

    Refer to PROCEDURE - Step 2 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 2 [12/2017 - 08/2019]

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [08/2016 - 12/2017] , or refer to INITIALIZATION [12/2017 - 08/2019]

  4. REMOVE INSTRUMENT PANEL GARNISH LH 

    Refer to PROCEDURE - Step 4 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 4 [12/2017 - 08/2019]

  5. REMOVE FRONT DOOR SCUFF PLATE LH 

    Refer to PROCEDURE - Step 9 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 9 [12/2017 - 08/2019]

  6. REMOVE COWL SIDE TRIM BOARD LH 

    Refer to PROCEDURE - Step 3 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 3 [12/2017 - 08/2019]

  7. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 7 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 7 [12/2017 - 08/2019]

  8. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 8 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 8 [12/2017 - 08/2019]

  9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 9 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 9 [12/2017 - 08/2019]

  10. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL 

    Refer to PROCEDURE - Step 2 [09/2015 - 12/2017] , or refer to PROCEDURE - Step 2 [12/2017 - 08/2019]

  11. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL 

    Refer to PROCEDURE - Step 3 [09/2015 - 12/2017] , or refer to PROCEDURE - Step 3 [12/2017 - 08/2019]

  12. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT 

    Refer to PROCEDURE - Step 5 [09/2015 - 12/2017] , or refer to PROCEDURE - Step 5 [12/2017 - 08/2019]

  13. REMOVE LOWER INSTRUMENT FINISH PANEL SUB 

    Refer to PROCEDURE - Step 10 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 10 [12/2017 - 08/2019]

  14. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY 
    1. Disengage the 2 claws and 4 clips to separate the instrument cluster finish panel sub-assembly.
      GTY681602Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 4 clips as shown in the illustration.
      GTY635621Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    3. Disengage the 3 clips as shown in the illustration.
      GTY632600Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    4. Disconnect the connector to remove the instrument cluster finish panel sub-assembly.
  15. REMOVE COMBINATION METER ASSEMBLY 
    1. Remove the 4 screws.
      GTY653796Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the clamp.
    3. Disconnect each connector to remove the combination meter assembly.
scientia non olet · About LEMON Manuals