Installation [10/2017 - 10/2020]: Procedure

1. When reusing the rear pneumatic cylinder with shock absorber assembly LH:
   1. Install 2 new O-rings, a new plate and new No. 2 connector to the front pneumatic cylinder with shock absorber assembly LH.

      Refer to PRECAUTION [10/2017 - ]

2. Temporarily tighten the washer and rear pneumatic cylinder with shock absorber assembly LH with a new nut.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

3. Temporarily tighten the rear pneumatic cylinder with shock absorber assembly LH with the 3 nuts.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   HINT: 

   If the nut is hard to see, use a mirror.

1. Connect the No. 7 height control tube to the rear pneumatic cylinder with shock absorber assembly LH.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Refer to PRECAUTION [10/2017 - ]

1. Install the skid control sensor wire LH with the nut.

   Torque: 6.0 N.m (61 kgf/cm, 53 in.lbf) 

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Connect the connector.

See step  4

HINT: 

Move the air pressure according to the instructions on the Techstream.

Refer to PROCEDURE - Step 1

HINT: 

Move the air pressure according to the instructions on the Techstream.

Refer to PROCEDURE - Step 2

See step  5

1. Fully tighten the nut.

   Torque: 110 N.m (1122 kgf/cm, 81 ft.lbf) 

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Fully tighten the 2 nuts A.

   Torque: 40 N.m (408 kgf/cm, 30 ft.lbf) 

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Torque Wrench Fulcrum Length

   HINT: 

   If the nut is hard to see, use a mirror.

3. Using SST, fully tighten the nut B.
   • SST: 09249-37010 

   Specified tightening torque 

   Torque: 40 N.m (408 kgf/cm, 30 ft.lbf) 

   HINT: 

   • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

     Refer to PRECAUTION [10/2017 - 09/2019] , or refer to PRECAUTION [09/2019 - 10/2020]

   • When using SST (fulcrum length of 100 mm (3.937 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 25.7 N.m (262 kgf/cm, 19 ft.lbf)
   • If the nut is hard to see, use a mirror.

See step  7

See step  8

1. Install the rear wheel RH.

   Refer to INSTALLATION [10/2017 - 10/2023]

2. Check the connections of the tubes for air leakage.

   Refer to OPERATION CHECK [10/2017 - ]

3. Remove the rear wheel RH.

   Refer to REMOVAL [10/2017 - 10/2023]

HINT: 

Use the same procedure for the RH and LH sides.

Refer to PROCEDURE - Step 4

Refer to PROCEDURE - Step 1

Refer to INSTALLATION [10/2017 - 10/2023]

Refer to PROCEDURE - Step 22

Refer to PROCEDURE - Step 3

Refer to PROCEDURE - Step 24

HINT: 

Use the same procedure described for the LH side.

Refer to ADJUSTMENT [10/2017 - 10/2020]

Refer to ADJUSTMENT [10/2017 - 10/2020]

Refer to OPERATION CHECK [10/2017 - ]

Refer to INITIALIZATION [10/2017 - 09/2018] , or refer to INITIALIZATION [09/2018 - 10/2020]

Refer to ADJUSTMENT [10/2017 - 10/2020]