LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> LS 500h AWD >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Audio / Video System - Diagnostic Codes (3 Of 3) & Symptom Tests (1 Of 2) >> Audio And Visual System >> DTC U11D0-87: Lost Local Communication with MET Missing Message; DTC U11D1-87: Lost Local Communication with HUD Missing Message; DTC U11D2-87: Lost Local Communication with Clock Missing Message [10/2022 - 10/2023] >> Procedure

DTC U11D0-87: Lost Local Communication with MET Missing Message; DTC U11D1-87: Lost Local Communication with HUD Missing Message; DTC U11D2-87: Lost Local Communication with Clock Missing Message [10/2022 - 10/2023]: Procedure

  1. CHECK VEHICLE TYPE 
    1. Check the vehicle type.

      Result

      Result Proceed to
      w/o Headup Display A
      w/ Headup Display B

    Result: 

    B 

    See step  4

    Result: 

    A 

    See step  2

  2. CHECK FOR DTC 
    1. Check for DTCs and proceed to the following step.

      Body Electrical > Navigation System > Trouble Codes 

      Body Electrical > Combination Meter > Trouble Codes 

      Pattern GTS Display
      Navigation System Combination Meter
      Pattern 1 U11D0-87
      U11D2-87      		 B1321-87
      Pattern 2 U11D0-87 B1321-87
      Pattern 3 U11D2-87 -
      Pattern 4 U11D0-87
      U11D2-87      		 -

      Result

      Result Proceed to
      Pattern 1 A
      Pattern 2 B
      Pattern 3 C
      Pattern 4 D

    Result: 

    B 

    See step  9

    Result: 

    C 

    See step  11

    Result: 

    D 

    REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    A 

    See step  3

  3. CHECK CLOCK ASSEMBLY 

    Pre-procedure1

    1. Disconnect the G167 clock assembly connector.

      Procedure1

    2. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTCs U11D0-87 and U11D2-87 are output A
      DTC U11D2-87 is output B

      Post-procedure1

    3. None

    Result: 

    A 

    See step  7

    Result: 

    B 

    REPLACE CLOCK ASSEMBLY. Refer to  REMOVAL [10/2020 - ] 

  4. CHECK FOR DTC 
    1. Check for DTCs and proceed to the following step.

      Body Electrical > Navigation System > Trouble Codes 

      Body Electrical > Combination Meter > Trouble Codes 

      Body Electrical > Head Up Display > Trouble Codes 

      Pattern GTS Display
      Navigation System Combination Meter Head Up Display
      Pattern 1 U11D0-87
      U11D1-87
      U11D2-87      		 B1321-87 B1321-87
      Pattern 2 U11D0-87 B1321-87 -
      Pattern 3 U11D1-87 - B1321-87
      Pattern 4 U11D2-87 - -
      Pattern 5 U11D0-87
      U11D1-87
      U11D2-87      		 - -

      Result

      Result Proceed to
      Pattern 1 A
      Pattern 2 B
      Pattern 3 C
      Pattern 4 D
      Pattern 5 E

    Result: 

    B 

    See step  9

    Result: 

    C 

    See step  10

    Result: 

    D 

    See step  11

    Result: 

    E 

    REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    A 

    See step  5

  5. CHECK METER MIRROR SUB-ASSEMBLY 

    Pre-procedure1

    1. Disconnect the meter mirror sub-assembly connector.

      Procedure1

    2. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTCs U11D0-87, U11D1-87 and U11D2-87 are output A
      DTC U11D1-87 is output B

      Post-procedure1

    3. None

    Result: 

    B 

    REPLACE METER MIRROR SUB-ASSEMBLY. Refer to  REMOVAL [10/2022 - 10/2023] 

    Result: 

    A 

    See step  6

  6. CHECK CLOCK ASSEMBLY 

    Pre-procedure1

    1. Disconnect the G167 clock assembly connector.

      Procedure1

    2. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTCs U11D0-87 and U11D2-87 are output A
      DTC U11D2-87 is output B

      Post-procedure1

    3. None

    Result: 

    B 

    REPLACE CLOCK ASSEMBLY. Refer to  REMOVAL [10/2020 - ] 

    Result: 

    A 

    See step  7

  7. CHECK FOR CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE) 

    Pre-procedure1

    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the G34*1 or G161*2 combination meter assembly connector.
      1. *1: w/o Advanced Drive System
      2. *2: w/ Advanced Drive System

      Procedure1

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      W/O ADVANCED DRIVE SYSTEM

      Tester Connection Condition Specified Condition
      G34-8 (TX+) - G34-7 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
      G34-8 (TX+) - G112-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      G34-7 (TX-) - G112-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      G34-8 (TX+) - G112-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      G34-7 (TX-) - G112-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      W/ ADVANCED DRIVE SYSTEM

      Tester Connection Condition Specified Condition
      G161-32 (TX+) - G161-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
      G161-32 (TX+) - G112-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      G161-15 (TX-) - G112-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      G161-32 (TX+) - G112-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      G161-15 (TX-) - G112-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    4. None

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2021 - 10/2023] 

    Result: 

    NG 

    See step  8

  8. CHECK FOR CAN BUS WIRE (RADIO RECEIVER ASSEMBLY MAIN WIRE) 

    Pre-procedure1

    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the G186 radio receiver assembly connector.

      Procedure1

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G186-11 (CNH1) - G186-12 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
      G186-11 (CNH1) - G112-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      G186-12 (CNL1) - G112-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      G186-11 (CNH1) - G112-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      G186-12 (CNL1) - G112-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    4. None

    Result: 

    OK 

    REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  9. CHECK FOR CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE) 

    Pre-procedure1

    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the G34*1 or G161*2 combination meter assembly connector.

      Procedure1

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      W/O ADVANCED DRIVE SYSTEM

      Tester Connection Condition Specified Condition
      G34-8 (TX+) - G34-7 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
      W/ ADVANCED DRIVE SYSTEM

      Tester Connection Condition Specified Condition
      G161-32 (TX+) - G161-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    4. None

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2021 - 10/2023] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  10. CHECK FOR CAN BUS WIRE (METER MIRROR SUB-ASSEMBLY BRANCH WIRE) 

    Pre-procedure1

    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the G88 meter mirror sub-assembly connector.

      Procedure1

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G88-14 (TX+) - G88-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    4. None

    Result: 

    OK 

    REPLACE METER MIRROR SUB-ASSEMBLY. Refer to  REMOVAL [10/2022 - 10/2023] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  11. CHECK FOR CAN BUS WIRE (CLOCK ASSEMBLY BRANCH WIRE) 

    Pre-procedure1

    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the G167 mobile wireless charger cradle assembly connector.

      Procedure1

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G167-4 (TX+1) - G167-5 (TX-1) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    4. None

    Result: 

    OK 

    REPLACE CLOCK ASSEMBLY. Refer to  REMOVAL [10/2020 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals