LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> LS 500h AWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Entertainment Systems >> Audio / Video System - Diagnostic Codes (2 Of 3) >> Audio And Visual System >> DTC B15C3-71: Speaker Output Short Actuator Stuck [10/2022 - ] >> Procedure

DTC B15C3-71: Speaker Output Short Actuator Stuck [10/2022 - ]: Procedure

  1. CHECK VEHICLE TYPE 
    1. Check the vehicle type.

      Result

      Result Proceed to
      for 12 Speakers A
      for 23 Speakers B

    Result: 

    See step  14

    Result: 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT) 
    1. *1: for RH Side

      *2: for LH Side

    1. Disconnect the L52 stereo component amplifier assembly connector.
    2. Disconnect the H1*1 and/or H19*2 front No. 1 speaker assembly connector.
    3. Disconnect the G69*1 and/or G70*2 front No. 2 speaker assembly connector.
    4. Disconnect the G50 front No. 3 speaker assembly connector.
    5. Disconnect the K11*1 and/or K25*2 rear speaker assembly connector.
    6. Disconnect the K10*1 and/or K24*2 rear No. 2 speaker assembly connector.
    7. Disconnect the L15 rear No. 3 speaker assembly connector.
    8. Disconnect the G165 DCM (telematics transceiver) connector.
    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      FOR RH SIDE

      Tester Connection Condition Specified Condition
      L52-5 (WFR+) - H1-2 (+) Always Below 1 Ω
      L52-20 (WFR-) - H1-1 (-) Always Below 1 Ω
      L52-13 (FR+) - G165-1 (SPI+) Always Below 1 Ω
      L52-28 (FR-) - G165-2 (SPI-) Always Below 1 Ω
      G165-3 (SPO+) - G69-2 (+) Always Below 1 Ω
      G165-4 (SPO-) - G69-1 (-) Always Below 1 Ω
      L52-9 (TWR+) - K10-3 (+TW) Always Below 1 Ω
      L52-24 (TWR-) - K10-1 (-TW) Always Below 1 Ω
      K10-4 (+) - K11-2 (+) Always Below 1 Ω
      K10-2 (-) - K11-1 (-) Always Below 1 Ω
      L52-5 (WFR+) - Body ground Always 10 kΩ or higher
      L52-20 (WFR-) - Body ground Always 10 kΩ or higher
      L52-13 (FR+) - Body ground Always 10 kΩ or higher
      L52-28 (FR-) - Body ground Always 10 kΩ or higher
      G165-3 (SPO+) - Body ground Always 10 kΩ or higher
      G165-4 (SPO-) - Body ground Always 10 kΩ or higher
      L52-9 (TWR+) - Body ground Always 10 kΩ or higher
      L52-24 (TWR-) - Body ground Always 10 kΩ or higher
      K10-4 (+) - Body ground Always 10 kΩ or higher
      K10-2 (-) - Body ground Always 10 kΩ or higher
      FOR LH SIDE

      Tester Connection Condition Specified Condition
      L52-4 (WFL+) - H19-2 (+) Always Below 1 Ω
      L52-19 (WFL-) - H19-1 (-) Always Below 1 Ω
      L52-12 (FL+) - G70-2 (+) Always Below 1 Ω
      L52-27 (FL-) - G70-1 (-) Always Below 1 Ω
      L52-8 (TWL+) - K24-3 (+TW) Always Below 1 Ω
      L52-23 (TWL-) - K24-1 (-TW) Always Below 1 Ω
      K24-4 (+) - K25-2 (+) Always Below 1 Ω
      K24-2 (-) - K25-1 (-) Always Below 1 Ω
      L52-4 (WFL+) - Body ground Always 10 kΩ or higher
      L52-19 (WFL-) - Body ground Always 10 kΩ or higher
      L52-12 (FL+) - Body ground Always 10 kΩ or higher
      L52-27 (FL-) - Body ground Always 10 kΩ or higher
      L52-8 (TWL+) - Body ground Always 10 kΩ or higher
      L52-23 (TWL-) - Body ground Always 10 kΩ or higher
      K24-4 (+) - Body ground Always 10 kΩ or higher
      K24-2 (-) - Body ground Always 10 kΩ or higher
      FOR CENTER SIDE

      Tester Connection Condition Specified Condition
      L52-7 (CTR+) - G50-2 (+) Always Below 1 Ω
      L52-22 (CTR-) - G50-1 (-) Always Below 1 Ω
      L52-6 (WF1+) - L15-2 (WF1+) Always Below 1 Ω
      L52-21 (WF1-) - L15-1 (WF1-) Always Below 1 Ω
      L52-7 (CTR+) - Body ground Always 10 kΩ or higher
      L52-22 (CTR-) - Body ground Always 10 kΩ or higher
      L52-6 (WF1+) - Body ground Always 10 kΩ or higher
      L52-21 (WF1-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  3

  3. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY 

    Refer to INSPECTION [10/2017 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2017 - ] 

    Result: 

    OK 

    See step  4

  4. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 

    Refer to INSPECTION [10/2017 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2017 - ] 

    Result: 

    OK 

    See step  5

  5. INSPECT REAR SPEAKER ASSEMBLY 

    Refer to INSPECTION [10/2017 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2017 - ] 

    Result: 

    OK 

    See step  6

  6. INSPECT REAR NO. 3 SPEAKER ASSEMBLY 

    Refer to INSPECTION [10/2017 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2022 - 10/2023]  , or refer to  REMOVAL [10/2023 - ] 

    Result: 

    OK 

    See step  7

  7. INSPECT DCM (TELEMATICS TRANSCEIVER) (SPO+, SPO-, SPI+, SPI-) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

      GTY961378Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM [Telematics Transceiver])
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 (SPO+) - 1 (SPI+) Always Below 1 Ω
      4 (SPO-) - 2 (SPI-) Always Below 1 Ω
      1 (SPI+) - 2 (SPI-) Always 10 kΩ or higher
      3 (SPO+) - 4 (SPO-) Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [10/2022 - 10/2023]  , or refer to  REMOVAL [10/2023 - ] 

    Result: 

    OK 

    See step  8

  8. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Replace the front No. 2 speaker assembly with a new or known good one.

      HINT: 

      Refer to REMOVAL [10/2017 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  9

  9. CLEAR DTC 
    1. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  10

  10. CHECK FOR DTC 
    1. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTCs are not output A
      DTCs are output B

    Result: 

    END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

    Result: 

    See step  11

  11. CHECK REAR NO. 2 SPEAKER ASSEMBLY 
    1. Replace the rear No. 2 speaker assembly with a new or known good one.

      HINT: 

      Refer to REMOVAL [10/2017 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  12

  12. CLEAR DTC 
    1. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  13

  13. CHECK FOR DTC 
    1. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTCs are not output A
      DTCs are output B

    Result: 

    END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

    Result: 

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY. Refer to  REMOVAL [10/2022 - 10/2023]  , or refer to  REMOVAL [10/2023 - ] 

  14. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT) 
    1. *1: for RH Side

      *2: for LH Side

    1. Disconnect the L52 and L54 stereo component amplifier assembly connectors.
    2. Disconnect the H1*1 and/or H19*2 front No. 1 speaker assembly connector.
    3. Disconnect the G69*1 and/or G70*2 front No. 2 speaker assembly connector.
    4. Disconnect the G50 front No. 3 speaker assembly connector.
    5. Disconnect the N20*1 and/or N21*2 roof speaker assembly (front) connector.
    6. Disconnect the K11*1 and/or K25*2 rear speaker assembly connector.
    7. Disconnect the K9*1 and/or K23*2 rear No. 2 speaker assembly (rear door) connector.
    8. Disconnect the N22*1 and/or N23*2 roof speaker assembly (rear) connector.
    9. Disconnect the L13*1 and/or L14*2 rear No. 2 speaker assembly (rear tray) connector.
    10. Disconnect the L15 rear No. 3 speaker assembly connector.
    11. Disconnect the G165 DCM (telematics transceiver) connector.
    12. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      FOR RH SIDE

      Tester Connection Condition Specified Condition
      L52-5 (WFR+) - H1-2 (+) Always Below 1 Ω
      L52-20 (WFR-) - H1-1 (-) Always Below 1 Ω
      L52-13 (FR+) - G165-1 (SPI+) Always Below 1 Ω
      L52-28 (FR-) - G165-2 (SPI-) Always Below 1 Ω
      G165-3 (SPO+) - G69-2 (+) Always Below 1 Ω
      G165-4 (SPO-) - G69-1 (-) Always Below 1 Ω
      L52-9 (TWR+) - K9-2 (+) Always Below 1 Ω
      L52-24 (TWR-) - K9-1 (-) Always Below 1 Ω
      L54-2 (ROR+) - N20-2 (+) Always Below 1 Ω
      L54-6 (ROR-) - N20-1 (-) Always Below 1 Ω
      L52-15 (RR+) - K11-2 (+) Always Below 1 Ω
      L52-30 (RR-) - K11-1 (-) Always Below 1 Ω
      L54-4 (R-R+) - N22-2 (+) Always Below 1 Ω
      L54-10 (R-R-) - N22-1 (-) Always Below 1 Ω
      L52-11 (SR+) - L13-2 (+) Always Below 1 Ω
      L52-26 (SR-) - L13-1 (-) Always Below 1 Ω
      L52-5 (WFR+) - Body ground Always 10 kΩ or higher
      L52-20 (WFR-) - Body ground Always 10 kΩ or higher
      L52-13 (FR+) - Body ground Always 10 kΩ or higher
      L52-28 (FR-) - Body ground Always 10 kΩ or higher
      G165-3 (SPO+) - Body ground Always 10 kΩ or higher
      G165-4 (SPO-) - Body ground Always 10 kΩ or higher
      L52-9 (TWR+) - Body ground Always 10 kΩ or higher
      L52-24 (TWR-) - Body ground Always 10 kΩ or higher
      L54-2 (ROR+) - Body ground Always 10 kΩ or higher
      L54-6 (ROR-) - Body ground Always 10 kΩ or higher
      L52-15 (RR+) - Body ground Always 10 kΩ or higher
      L52-30 (RR-) - Body ground Always 10 kΩ or higher
      L54-4 (R-R+) - Body ground Always 10 kΩ or higher
      L54-10 (R-R-) - Body ground Always 10 kΩ or higher
      L52-11 (SR+) - Body ground Always 10 kΩ or higher
      L52-26 (SR-) - Body ground Always 10 kΩ or higher
      FOR LH SIDE

      Tester Connection Condition Specified Condition
      L52-4 (WFL+) - H19-2 (+) Always Below 1 Ω
      L52-19 (WFL-) - H19-1 (-) Always Below 1 Ω
      L52-12 (FL+) - G70-2 (+) Always Below 1 Ω
      L52-27 (FL-) - G70-1 (-) Always Below 1 Ω
      L52-8 (TWL+) - K23-2 (+) Always Below 1 Ω
      L52-23 (TWL-) - K23-1 (-) Always Below 1 Ω
      L54-1 (ROL+) - N21-2 (+) Always Below 1 Ω
      L54-5 (ROL-) - N21-1 (-) Always Below 1 Ω
      L52-14 (RL+) - K25-2 (+) Always Below 1 Ω
      L52-29 (RL-) - K25-1 (-) Always Below 1 Ω
      L54-3 (R-L+) - N23-2 (+) Always Below 1 Ω
      L54-9 (R-L-) - N23-1 (-) Always Below 1 Ω
      L52-10 (SL+) - L14-2 (+) Always Below 1 Ω
      L52-25 (SL-) - L14-1 (-) Always Below 1 Ω
      L52-4 (WFL+) - Body ground Always 10 kΩ or higher
      L52-19 (WFL-) - Body ground Always 10 kΩ or higher
      L52-12 (FL+) - Body ground Always 10 kΩ or higher
      L52-27 (FL-) - Body ground Always 10 kΩ or higher
      L52-8 (TWL+) - Body ground Always 10 kΩ or higher
      L52-23 (TWL-) - Body ground Always 10 kΩ or higher
      L54-1 (ROL+) - Body ground Always 10 kΩ or higher
      L54-5 (ROL-) - Body ground Always 10 kΩ or higher
      L52-14 (RL+) - Body ground Always 10 kΩ or higher
      L52-29 (RL-) - Body ground Always 10 kΩ or higher
      L54-3 (R-L+) - Body ground Always 10 kΩ or higher
      L54-9 (R-L-) - Body ground Always 10 kΩ or higher
      L52-10 (SL+) - Body ground Always 10 kΩ or higher
      L52-25 (SL-) - Body ground Always 10 kΩ or higher
      FOR CENTER SIDE

      Tester Connection Condition Specified Condition
      L52-7 (CTR+) - G50-2 (+) Always Below 1 Ω
      L52-22 (CTR-) - G50-1 (-) Always Below 1 Ω
      L52-6 (WF1+) - L15-2 (WF1+) Always Below 1 Ω
      L52-21 (WF1-) - L15-1 (WF1-) Always Below 1 Ω
      L52-7 (CTR+) - Body ground Always 10 kΩ or higher
      L52-22 (CTR-) - Body ground Always 10 kΩ or higher
      L52-6 (WF1+) - Body ground Always 10 kΩ or higher
      L52-21 (WF1-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  15

  15. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 

    Refer to INSPECTION [10/2017 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2017 - ] 

    Result: 

    OK 

    See step  16

  16. INSPECT ROOF SPEAKER ASSEMBLY (FRONT) 

    Refer to INSPECTION [10/2017 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE ROOF SPEAKER ASSEMBLY (FRONT). Refer to  REMOVAL [10/2022 - 10/2023]  , or refer to  REMOVAL [10/2023 - ] 

    Result: 

    OK 

    See step  17

  17. INSPECT ROOF SPEAKER ASSEMBLY (REAR) 

    Refer to INSPECTION [10/2017 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE ROOF SPEAKER ASSEMBLY (REAR). Refer to  REMOVAL [10/2022 - 10/2023]  , or refer to  REMOVAL [10/2023 - ] 

    Result: 

    OK 

    See step  18

  18. INSPECT REAR SPEAKER ASSEMBLY 

    Refer to INSPECTION [10/2017 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2017 - ] 

    Result: 

    OK 

    See step  19

  19. INSPECT REAR NO. 3 SPEAKER ASSEMBLY 

    Refer to INSPECTION [10/2017 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2022 - 10/2023]  , or refer to  REMOVAL [10/2023 - ] 

    Result: 

    OK 

    See step  20

  20. INSPECT DCM (TELEMATICS TRANSCEIVER) (SPO+, SPO-, SPI+, SPI-) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

      GTY961378Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM [Telematics Transceiver])
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 (SPO+) - 1 (SPI+) Always Below 1 Ω
      4 (SPO-) - 2 (SPI-) Always Below 1 Ω
      1 (SPI+) - 2 (SPI-) Always 10 kΩ or higher
      3 (SPO+) - 4 (SPO-) Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [10/2022 - 10/2023]  , or refer to  REMOVAL [10/2023 - ] 

    Result: 

    OK 

    See step  21

  21. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Replace the front No. 2 speaker assembly with a new or known good one.

      HINT: 

      Refer to REMOVAL [10/2017 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  22

  22. CLEAR DTC 
    1. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  23

  23. CHECK FOR DTC 
    1. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTCs are not output A
      DTCs are output B

    Result: 

    END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

    Result: 

    See step  24

  24. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Replace the front No. 3 speaker assembly with a new or known good one.

      HINT: 

      Refer to REMOVAL [10/2017 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  25

  25. CLEAR DTC 
    1. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  26

  26. CHECK FOR DTC 
    1. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTCs are not output A
      DTCs are output B

    Result: 

    END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE) 

    Result: 

    See step  27

  27. REPLACE REAR NO. 2 SPEAKER ASSEMBLY [REAR DOOR] 
    1. Replace the rear No. 2 speaker assembly (rear door) with a new or known good one.

      HINT: 

      Refer to REMOVAL [10/2017 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  28

  28. CLEAR DTC 
    1. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  29

  29. CHECK FOR DTC 
    1. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTCs are not output A
      DTCs are output B

    Result: 

    END (REAR NO. 2 SPEAKER ASSEMBLY [REAR DOOR] IS DEFECTIVE) 

    Result: 

    See step  30

  30. REPLACE REAR NO. 2 SPEAKER ASSEMBLY [REAR TRAY] 
    1. Replace the rear No. 2 speaker assembly (rear tray) with a new or known good one.

      HINT: 

      Refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  31

  31. CLEAR DTC 
    1. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  32

  32. CHECK FOR DTC 
    1. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTCs are not output A
      DTCs are output B

    Result: 

    END (REAR NO. 2 SPEAKER ASSEMBLY [REAR TRAY] IS DEFECTIVE) 

    Result: 

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY. Refer to  REMOVAL [10/2022 - 10/2023]  , or refer to  REMOVAL [10/2023 - ]