Steering Pad Switch Circuit [12/2017 - 10/2022]: Procedure

1. Remove the steering pad switch assembly.

   Refer to REMOVAL [12/2017 - 09/2018] , or refer to REMOVAL [09/2018 - 10/2020] , or refer to REMOVAL [10/2020 - 10/2022]

2. Inspect the steering pad switch assembly.

   Refer to INSPECTION [12/2017 - 10/2023]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE STEERING PAD SWITCH ASSEMBLY. Refer to  REMOVAL [12/2017 - 09/2018]  , or refer to  REMOVAL [09/2018 - 10/2020]  , or refer to  REMOVAL [10/2020 - 10/2022] 

Result: 

OK 

See step  2

1. Remove the spiral with sensor cable sub-assembly.

   Refer to REMOVAL [12/2017 - 09/2018] , or refer to REMOVAL [09/2018 - 10/2020] , or refer to REMOVAL [10/2020 - 10/2022]

2. Inspect the spiral with sensor cable sub-assembly.

   Refer to INSPECTION [12/2017 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY. Refer to  REMOVAL [12/2017 - 09/2018]  , or refer to  REMOVAL [09/2018 - 10/2020]  , or refer to  REMOVAL [10/2020 - 10/2022] 

Result: 

OK 

See step  3

1. Disconnect the G34 combination meter assembly connector.
2. Disconnect the G27 spiral with sensor cable sub-assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   G34-2 (MSM+) - G27-11 (+DP)	Always	Below 1 Ω
   G34-3 (MSTI) - G27-10 (+DP2)	Always	Below 1 Ω
   G34-2 (MSM+) - Other terminals and body ground	Always	10 kΩ or higher
   G34-3 (MSTI) - Other terminals and body ground	Always	10 kΩ or higher
   G27-4 (EAU) - Body ground	Always	Below 1 Ω

   Result

   Result	Proceed to
   OK	A
   NG (Spiral with sensor cable sub-assembly - combination meter assembly)	B
   NG (Spiral with sensor cable sub-assembly - body ground)	C

Result: 

A 

REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [12/2017 - 10/2020]  , or refer to  REMOVAL [10/2020 - 10/2023] 

Result: 

B 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

C 

See step  4

1. Disconnect the G52 radio receiver assembly connector.
2. Disconnect the G27 spiral with sensor cable sub-assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   G52-24 (SWG) - G27-4 (EAU)	Always	Below 1 Ω
   G52-1 (GND1) - Body ground	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [12/2017 - 10/2022] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR