Removal [03/2017 - ]: Procedure
- REMOVE NO. 1 DECK BOARD
See step 10 [03/2017 - 01/2021], or see step 11 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE NO. 2 DECK BOARD
See step 11 [03/2017 - 01/2021], or see step 12 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE LUGGAGE COMPARTMENT TRIM COVER LH
See step 12 [03/2017 - 01/2021], or see step 13 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE LUGGAGE COMPARTMENT TRIM COVER RH
See step 13 [03/2017 - 01/2021], or see step 14 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE SIDE TRIM BOX
See step 14 [03/2017 - 01/2021], or see step 15 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE REAR FLOOR FINISH PLATE
See step 15 [03/2017 - 01/2021], or see step 16 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE LUGGAGE COMPARTMENT TRIM BOX
See step 16 [03/2017 - 01/2021], or see step 17 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
Refer to PROCEDURE - Step 1
- REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER
See step 18 [03/2017 - 01/2021], or see step 19 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER LH
See step 19 [03/2017 - 01/2021], or see step 20 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER RH
See step 20 [03/2017 - 01/2021], or see step 21 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE LUGGAGE COMPARTMENT DOOR ASSIST GRIP
See step 1 [03/2017 - 01/2021], or see step 1 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE LUGGAGE COMPARTMENT DOOR COVER
See step 2 [03/2017 - 01/2021], or see step 2 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE NO. 4 LUGGAGE ROOM WIRE
See step 21 [03/2017 - 01/2021], or see step 22 [01/2021 - 05/2023], or refer to DISASSEMBLY [05/2023 - ]
- REMOVE NO. 6 ANTENNA CORD SUB-ASSEMBLY
Refer to PROCEDURE - Step 16
- REMOVE REAR BUMPER COVER
Refer to REMOVAL [03/2017 - ]
- REMOVE REAR COMBINATION LIGHT BODY BRACKET LH
- REMOVE REAR COMBINATION LIGHT BODY BRACKET RH
HINT:
Use the same procedure described for the LH side.
- REMOVE UPPER QUARTER WINDOW MOULDING LH
Refer to PROCEDURE - Step 3
- REMOVE UPPER QUARTER WINDOW MOULDING RH
HINT:
Use the same procedure described for the LH side.
- REMOVE UPPER NO. 1 LUGGAGE COMPARTMENT COVER LH
HINT:
When removing the upper No. 1 luggage compartment cover LH, heat the upper No. 1 luggage compartment cover LH using a heat light.
Standard
Item Temperature Upper No. 1 Luggage Compartment Cover LH 20 to 30°C (68 to 86°F) - REMOVE UPPER NO. 1 LUGGAGE COMPARTMENT COVER RH
HINT:
Use the same procedure described for the LH side.
- REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER LH
HINT:
When removing the luggage compartment door hinge cover LH, heat the luggage compartment door hinge cover LH using a heat light.
Standard
Item Temperature Luggage Compartment Door Hinge Cover LH 20 to 30°C (68 to 86°F) - REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER RH
HINT:
Use the same procedure described for the LH side.
- REMOVE LOWER OUTSIDE BACK WINDOW MOULDING
HINT:
When removing the lower outside back window moulding, heat the lower outside back window moulding using a heat light.
Standard
Item Temperature Lower Outside Back Window Moulding 20 to 30°C (68 to 86°F) WARNING:- Do not touch the heat light and heated parts.
- Touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
*a Heated Part *b Heat Light Protective Tape Apply protective tape at the position as shown in the illustration.
- Using a clip remover, remove the clip.
Protective Tape - Using moulding remover A, scrape off the double-sided tape that holds.
Protective Tape Double-sided Tape Protective Tape Detach the clips and remove the lower outside back window moulding.
- REMOVE LUGGAGE COMPARTMENT DOOR WEATHERSTRIP