LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> IS 350 Base, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 70 (Engine Mechanical System (2GR-FSE) - Service Information (2 Of 2)) >> Engine Unit >> Removal [04/2013 - 10/2017] >> Procedure

Removal [04/2013 - 10/2017]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2017 Lexus IS 350, 2017 Lexus IS 300, 2016 Lexus IS 350, 2016 Lexus IS 300, and 2015 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE V-RIBBED BELT 

    Refer to PROCEDURE - Step 4

  2. REMOVE NO. 2 ENGINE COVER 
    1. Disconnect the clamp from the No. 2 engine cover sub-assembly.
      GTY466857Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 3 clips and No. 2 engine cover sub-assembly.
  3. REMOVE NO. 1 ENGINE COVER 

    Refer to PROCEDURE - Step 6

  4. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 12

  5. REMOVE GENERATOR ASSEMBLY 

    Refer to PROCEDURE - Step 10

  6. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (for 2WD) 

    Refer to PROCEDURE - Step 7 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 9 [08/2015 - 10/2017]

  7. REMOVE OIL FILTER BRACKET (for AWD) 

    Refer to PROCEDURE - Step 7 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 7 [08/2015 - 10/2017]

  8. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (for AWD) 

    Refer to PROCEDURE - Step 9 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 9 [08/2015 - 10/2017]

  9. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH 
    1. Disconnect the 2 clamps.
      GTY461441Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for 2WD
      *B for AWD
    2. Remove the 4 bolts and front No. 1 engine mounting bracket LH from the cylinder block sub-assembly.
  10. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH 
    1. Remove the 4 bolts and front No. 1 engine mounting bracket RH from the cylinder block sub-assembly.
      GTY468930Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for 2WD
      *B for AWD
  11. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY 

    Refer to PROCEDURE - Step 9

  12. REMOVE WATER PUMP PULLEY 

    Refer to PROCEDURE - Step 13

  13. REMOVE ENGINE WIRE 
    1. Remove the engine wire from the engine assembly.
  14. REMOVE INJECTOR DRIVER 

    Refer to PROCEDURE - Step 7

  15. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY 

    Refer to PROCEDURE - Step 7 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 7 [08/2015 - 10/2017]

  16. REMOVE INTAKE AIR SURGE TANK ASSEMBLY 

    Refer to PROCEDURE - Step 6

  17. REMOVE NO. 2 SURGE TANK STAY 
    1. Disconnect the 2 clamps from the No. 2 surge tank stay.
      GTY466856Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt and No. 2 surge tank stay from the camshaft housing sub-assembly LH.
  18. REMOVE NO. 3 WATER BY-PASS PIPE 
    1. Remove the bolt and No. 3 water by-pass pipe from the camshaft housing sub-assembly RH.
      GTY456156Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 3 Water By-pass Pipe
      *2 No. 8 Water By-pass Hose
      *3 No. 9 Water By-pass Hose
    2. Slide the clip and disconnect the No. 8 water by-pass hose from the water outlet pipe assembly.
    3. Slide the clip and disconnect the No. 9 water by-pass hose from the rear water by-pass joint.
  19. REMOVE FUEL TUBE SUB-ASSEMBLY 
    1. Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly.

      Refer to PRECAUTION [04/2013 - 10/2017]

    2. Remove the fuel tube sub-assembly with the 2 bolts.
  20. REMOVE INTAKE MANIFOLD 

    Refer to PROCEDURE - Step 8

  21. REMOVE FUEL PRESSURE PULSATION DAMPER ASSEMBLY 

    Refer to PROCEDURE - Step 7 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 7 [08/2015 - 10/2017]

  22. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 7

  23. DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 8

  24. REMOVE FUEL PUMP ASSEMBLY 

    Refer to PROCEDURE - Step 9

  25. REMOVE NO. 3 FUEL PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 2

  26. REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 10

  27. REMOVE WIRE HARNESS CLAMP BRACKET 
    1. Remove the bolt and wire harness clamp bracket from the camshaft housing sub-assembly RH.
      GTY456901Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. REMOVE V-BANK COVER BRACKET SUB-ASSEMBLY 
    1. Remove the bolt and V-bank cover bracket sub-assembly from the cylinder head cover sub-assembly RH.
      GTY466859Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. REMOVE IGNITION COIL ASSEMBLY 

    Refer to PROCEDURE - Step 4

scientia non olet · About LEMON Manuals