LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> ES 300h Luxury >> Repair and Diagnosis >> Hybrid/Electric Powertrain >> Testing and Diagnosis >> Hybrid Control System (For Nickel Metal Hydride Battery) - Diagnostic Codes (5 Of 5) & Circuit Tests (1 Of 2) >> HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) >> DTC P3147-79: Transmission (Shaft) Mechanical Linkage Failure [06/2018 - ] >> Procedure

DTC P3147-79: Transmission (Shaft) Mechanical Linkage Failure [06/2018 - ]: Procedure

  1. CHECK DTC OUTPUT (ENGINE) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / Engine / Trouble Codes.

      Powertrain > Engine > Trouble Codes 

    4. Check for DTCs.

      Result

      Result Proceed to
      No DTCs are output, or DTCs except the ones in the table below are also output A
      Any of the following DTCs are also output B
      Relevant DTC
      P0335-11 Crankshaft Position Sensor "A" Circuit Short to Ground
      P0335-15 Crankshaft Position Sensor "A" Circuit Short to Battery or Open
      P0335-2A Crankshaft Position Sensor "A" Signal Stuck in Range
      P0335-31 Crankshaft Position Sensor "A" No Signal
    5. Turn the power switch off.

    Result: 

    B 

    GO TO DTC CHART (SFI SYSTEM). Refer to  DIAGNOSTIC TROUBLE CODE CHART [06/2018 - 07/2019]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [07/2019 - 10/2019]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2019 - 08/2020]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2020 - 08/2021]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2021 - 09/2022]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2022 - ] 

    Result: 

    A 

    See step  2

  2. CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION) 

    Refer to PROCEDURE - Step 1

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    See step  7

    Result: 

    OK 

    See step  3

  3. CLEAR DTC 

    Refer to PROCEDURE - Step 2

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    See step  4

  4. CHECK ENGINE RACING 

    Refer to PROCEDURE - Step 3

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY. Refer to  REMOVAL [06/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

    Result: 

    OK 

    See step  5

  5. CHECK CREEP MOVEMENT 

    Refer to PROCEDURE - Step 4

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY. Refer to  REMOVAL [06/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

    Result: 

    OK 

    See step  6

  6. INSPECT ENGINE SPEED 

    Refer to PROCEDURE - Step 5

    Result

    Result Proceed to
    The absolute value of the difference is less than 500 rpm. A
    The absolute value of the difference is 500 rpm or more continuously for 1 second. B

    Result: 

    A 

    REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY. Refer to  REMOVAL [06/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

    Result: 

    B 

    REPLACE TRANSMISSION INPUT DAMPER ASSEMBLY. Refer to  REMOVAL [06/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

  7. CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION) 

    Refer to PROCEDURE - Step 6

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY. Refer to  REMOVAL [06/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE ENGINE 

scientia non olet · About LEMON Manuals