LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> ES 300h Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 31 (Engine Starting System (2GR-FKS) - Service Information) >> Starter >> Reassembly [06/2018 - ] >> Procedure

Reassembly [06/2018 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 350, 2023 Lexus ES 350, 2022 Lexus ES 350, 2021 Lexus ES 350, and 2020 Lexus ES 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL PLANETARY GEAR 
    1. Apply high-temperature grease to the 3 planetary gears, 3 planetary gear shafts and repair service starter kit.
      GTY741882Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      High-temperature Grease
    2. Install the 3 planetary gears to the repair service starter kit.
  2. INSTALL RUBBER SEAL 
    1. Install the rubber seal to the repair service starter kit.
  3. INSTALL STARTER ARMATURE ASSEMBLY 
    1. Install the starter armature assembly to the starter yoke assembly.
      NOTE:

      The magnet of the starter yoke assembly may attract the starter armature assembly when the starter armature assembly is installed, causing the magnet to break.

      GTY708984Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL STARTER BRUSH HOLDER ASSEMBLY 
    1. Hold the brush spring back and set the 4 brushes as shown in the illustration.
      GTY171733Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the starter brush holder assembly to the starter armature assembly and push in the 4 brushes as shown in the illustration.
      GTY171711Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Fit the protrusion of the grommet between the negative (-) brush holder plate and positive (+) motor lead wire.
      GTY513466Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Grommet
      *b Negative (-) Brush Holder Plate
      *c Positive (+) Motor Lead Wire
  5. INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY 
    1. Install the starter commutator end frame assembly to the starter yoke assembly.
      NOTE:

      Align the field coil lead wire rubber of the starter yoke assembly with the cutout of the starter commutator end frame assembly.

      GTY759056Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Field Coil Lead Wire Rubber
      *b Cutout
    2. Install the 2 screws.

      Torque: 1.5 N.m (15 kgf/cm, 13 in.lbf) 

  6. INSTALL STARTER ARMATURE PLATE 
    1. Align the starter armature plate so that the protrusion fits between the stoppers of the starter yoke assembly, and install the starter armature plate.
      NOTE:

      Make sure the protrusion of the starter armature plate is inserted between the stoppers of the starter yoke assembly.

      GTY790071Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Starter Yoke Assembly
      *2 Starter Armature Plate
      *a Stopper
      *b Protrusion
  7. INSTALL STARTER YOKE ASSEMBLY 
    1. Align the protrusion of the starter yoke assembly with the cutout of the repair service starter kit.
      GTY742527Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protrusion
      *b Cutout
    2. Using a T25 "TORX" socket wrench, install the starter yoke assembly with the 2 through bolts.

      Torque: 6.0 N.m (61 kgf/cm, 53 in.lbf) 

  8. INSTALL MAGNET STARTER SWITCH ASSEMBLY 
    1. Apply high-temperature grease to the plunger as shown in the illustration.
      GTY748566Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      High-temperature Grease
    2. Hang the hook of the magnet starter switch assembly on the pinion drive lever.
    3. Install the magnet starter switch assembly with the 2 nuts.

      Torque: 7.5 N.m (76 kgf/cm, 66 in.lbf) 

    4. Connect the field coil lead wire to the magnet starter switch assembly with the nut.

      Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

scientia non olet · About LEMON Manuals