Power Trunk Lid does not Operate Using Any Switches [06/2018 - 08/2021]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Back Door / Trouble Codes.
5. Clear the DTCs.

   Body Electrical > Back Door > Clear DTCs 

6. Check for DTCs.

   Body Electrical > Back Door > Trouble Codes 

   OK

   DTC is not output.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [06/2018 - 08/2021] 

Result: 

OK 

See step  2

1. Disconnect the R7 luggage closer motor assembly connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   R7-11 (GND) - Body ground	Always	Below 1 Ω

3. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   R7-8 (IG) - Body ground	Engine switch on (IG)	11 to 14 V
   	Engine switch off	Below 1 V
   R7-10 (ECUB) - Body ground	Always	11 to 14 V
   R7-12 (B) - Body ground	Always	11 to 14 V

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  3

1. Enter the following menus: Body Electrical / Main Body / Data List.
2. Read the Data List according to the display on the Techstream.

   Body Electrical > Main Body > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Trunk Main SW	Luggage door opening cancel switch assembly signal	OFF or ON	OFF: Luggage door opening cancel switch assembly off ON: Luggage door opening cancel switch assembly on	-

   Body Electrical > Main Body > Data List 

   Tester Display
   Trunk Main SW

   OK

   The Data List item changes according to the operation of the luggage door opening cancel switch assembly.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE LUGGAGE CLOSER MOTOR ASSEMBLY. Refer to  REMOVAL [06/2018 - 08/2021] 

Result: 

NG 

See step  4

1. Remove the luggage door opening cancel switch assembly.

   Refer to REMOVAL [06/2018 - 08/2021]

2. Inspect the luggage door opening cancel switch assembly.

   Refer to INSPECTION [06/2018 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE LUGGAGE DOOR OPENING CANCEL SWITCH ASSEMBLY. Refer to  REMOVAL [06/2018 - 08/2021] 

Result: 

OK 

See step  5

1. Disconnect the G37 main body ECU (multiplex network body ECU) connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   G61-2 (B) - G37-27 (TMSW)	Always	Below 1 Ω
   G61-1 (L) - Body ground	Always	Below 1 Ω
   G61-2 (B) or G37-27 (TMSW) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [06/2018 - 08/2021] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR