Luggage Compartment Door Closer does not Operate [06/2018 - 08/2021]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Back Door / Active Test.
5. Perform the Active Test according to the display on the Techstream.

   Body Electrical > Back Door > Active Test 

   Tester Display	Measurement Item	Control Range	Diagnostic Note
   PBD Motor	luggage closer motor operation	OFF, Forward or Reverse	-

   Body Electrical > Back Door > Active Test 

   Tester Display
   PBD Motor

   OK

   The luggage door closer assembly (closer motor) operates normally according to the Techstream operation.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  5

Result: 

OK 

See step  2

1. Enter the following menus: Body Electrical / Back Door / Data List.
2. Read the Data List according to the display on the GTS.

   Body Electrical > Back Door > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Pawl Position Switch	Luggage door closer assembly (pawl switch) signal	OFF or ON	OFF: Luggage door closer assembly except half-latched ON: Luggage door closer assembly half-latched	-

   Body Electrical > Back Door > Data List 

   Tester Display
   Pawl Position Switch

   OK

   The Data List display changes according to luggage compartment door operation.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE LUGGAGE CLOSER MOTOR ASSEMBLY. Refer to  REMOVAL [06/2018 - 08/2021] 

Result: 

NG 

See step  3

1. Disconnect the R7 luggage closer motor assembly connector.
2. Disconnect the R18 luggage door closer assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   R7-21 (SWG) - R18-12 (CSWE)	Always	Below 1 Ω
   R7-20 (PAWL) - R18-11 (CLS)	Always	Below 1 Ω
   R7-21 (SWG) or R18-12 (CSWE) - Body ground	Always	10 kΩ or higher
   R7-20 (PAWL) or R18-11 (CLS) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  4

1. Remove the luggage door closer assembly.

   Refer to REMOVAL [06/2018 - ]

2. Inspect the luggage door closer assembly. (Each switches)

   Refer to INSPECTION [06/2018 - ]

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE LUGGAGE CLOSER MOTOR ASSEMBLY. Refer to  REMOVAL [06/2018 - 08/2021] 

Result: 

NG 

REPLACE LUGGAGE DOOR CLOSER ASSEMBLY. Refer to  REMOVAL [06/2018 - ] 

1. Remove the luggage door closer assembly.

   Refer to REMOVAL [06/2018 - ]

2. Inspect the luggage door closer assembly. (Luggage door closer motor)

   Refer to INSPECTION [06/2018 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE LUGGAGE DOOR CLOSER ASSEMBLY. Refer to  REMOVAL [06/2018 - ] 

Result: 

OK 

See step  6

1. Disconnect the R7 luggage closer motor assembly connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   R7-2 (LCM+) - R18-8 (M+)	Always	Below 1 Ω
   R7-1 (LCM-) - R18-1 (M-)	Always	Below 1 Ω
   R7-2 (LCM+) or R18-8 (M+) - Body ground	Always	10 kΩ or higher
   R7-1 (LCM-) or R18-1 (M-) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE LUGGAGE CLOSER MOTOR ASSEMBLY. Refer to  REMOVAL [06/2018 - 08/2021] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR