Caution / Notice / Hint

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 350, 2023 Lexus ES 350, 2022 Lexus ES 350, 2021 Lexus ES 350, and 2020 Lexus ES 350. However, it is still accessible from the selected car via links, so may be relevant.

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during camshaft timing oil control solenoid assembly removal/installation are shown below.

NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane Tracing Assist System	Refer to INITIALIZATION [08/2021 - ]
		Pre-collision System
		Parking Support Brake System*1
		Lighting System
	Memorize steering angle neutral point	Parking Assist Monitor System	Refer to INITIALIZATION [06/2018 - 09/2022]
	Memorize steering angle neutral point	Panoramic View Monitor System	Refer to INITIALIZATION [06/2018 - 09/2022]
	Initialize power trunk lid system	Power Trunk Lid System	Refer to INITIALIZATION [06/2018 - ]
Replacement of ECM	Vehicle Identification Number (VIN) registration	MIL comes on	Refer to REGISTRATION [06/2018 - ]
Replacement of ECM	ECU communication ID registration (Immobiliser system)	Engine start function	Refer to REGISTRATION [08/2020 - 09/2022]
Gas leak from exhaust system is repaired	Inspection after repair	Poor idle, etc. Engine start function, etc.	Refer to INITIALIZATION [07/2019 - ]
Replacement of ECM (If transaxle compensation code read from ECM)	Perform reset memory*2 Transfer transaxle compensation code Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency	for Initialization: Refer to INITIALIZATION [06/2018 - ] for Registration: Refer to REGISTRATION [06/2018 - ]
Replacement of ECM (If transaxle compensation code not read from ECM)	Perform reset memory*2 Reset transaxle compensation code Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency
Replacement of ECM	Code registration (Smart access system with push-button start (for Start Function, Gasoline Model)	Wireless Door Lock Control System Smart Access System with Push-button Start (for Entry Function, Gasoline Model) Smart Access System with Push-button Start (for Start Function, Gasoline Model) Steering lock function	Refer to REGISTRATION [08/2020 - 09/2022]
Replacement of automatic transaxle fluid	ATF thermal degradation estimate reset	The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly	Refer to INITIALIZATION [06/2018 - ]
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement)	Rear television camera assembly optical axis adjustment (Back camera position setting)	Parking assist monitor system	for Initialization: Refer to INITIALIZATION [06/2018 - 09/2022] for Calibration: Refer to CALIBRATION [06/2018 - 09/2022]
	Perform headlight ECU sub-assembly LH initialization	Lighting system	Refer to INITIALIZATION [08/2021 - ]
Front wheel alignment adjustment	Perform "Reset Memory". Perform acceleration sensor zero point calibration and store system information memorization.	VSC is disabled or malfunctions DTCs are output Slip indicator light illuminates ABS warning light illuminates	Refer to UTILITY [06/2018 - ]
Replacement of front television camera assembly Replacement of front bumper assembly Replacement of radiator grille	Front television camera view adjustment	Panoramic View Monitor System	for Initialization. Refer to INITIALIZATION [06/2018 - 09/2022] for Calibration. Refer to CALIBRATION [06/2018 - 09/2022]

*1: When performing learning using the Techstream.
Refer to CALIBRATION [08/2021 - 09/2022]
*2: Not necessary when ECM replaced with new one

NOTE:

After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)