LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> ES 300h Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 19 (Engine Control System (2GR-FKS) - Service Information) >> ACTIVE CONTROL ENGINE MOUNT (for Front Side) >> Removal [06/2018 - ] >> Procedure

Removal [06/2018 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 350, 2023 Lexus ES 350, 2022 Lexus ES 350, 2021 Lexus ES 350, and 2020 Lexus ES 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE VACUUM SWITCHING VALVE (for Active Control Engine Mount System) 

    Refer to REMOVAL [06/2018 - ] 

  2. REMOVE V-BANK COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 19 [06/2018 - 10/2019] , or refer to PROCEDURE - Step 19 [10/2019 - 08/2021] , or refer to PROCEDURE - Step 19 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 19 [09/2022 - ]

  3. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH 

    Refer to PROCEDURE - Step 7 [06/2018 - 10/2019] , or refer to PROCEDURE - Step 7 [10/2019 - 08/2021] , or refer to PROCEDURE - Step 7 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 7 [09/2022 - ]

  4. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH 

    Refer to PROCEDURE - Step 8 [06/2018 - 10/2019] , or refer to PROCEDURE - Step 8 [10/2019 - 08/2021] , or refer to PROCEDURE - Step 8 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 8 [09/2022 - ]

  5. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 9 [06/2018 - 10/2019] , or refer to PROCEDURE - Step 9 [10/2019 - 08/2021] , or refer to PROCEDURE - Step 9 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 9 [09/2022 - ]

  6. REMOVE NO. 3 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 10 [06/2018 - 10/2019] , or refer to PROCEDURE - Step 10 [10/2019 - 08/2021] , or refer to PROCEDURE - Step 10 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 10 [09/2022 - ]

  7. REMOVE SUSPENSION TOWER DAMPER (w/ Performance Damper) 

    Refer to PROCEDURE - Step 4 [06/2018 - 08/2020] , or refer to PROCEDURE - Step 4 [08/2020 - ]

  8. REMOVE FRONT ENGINE MOUNTING INSULATOR 
    1. Disengage the 2 clamps to separate the vacuum hoses from the front engine mounting insulator.
      GTY763558Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the vacuum hose from the front engine mounting insulator.
      GTY763556Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Support the engine assembly with transaxle using a jack and wooden block.
      GTY769152Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Wooden Block Placement Location
    4. Remove the 4 bolts and front engine mounting bracket.
      GTY763564Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the 3 nuts and front engine mounting insulator from the front frame assembly.
      GTY763562Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Remove the nut and stay from the front engine mounting insulator.
      GTY763563Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals